D640D90VF datasheet(26/54 Pages) AMD

26 / 54 page

Am29DL640D

December 13, 2005

Enter Secured Silicon Sector command sequence.

The device continues to access the Secured Silicon

Sector region until the system issues the four-cycle

Exit Secured Silicon Sector command sequence. The

Exit Secured Silicon Sector command sequence re-

turns the device to normal operation. The Secured

Silicon Sector is not accessible when the device is ex-

ecuting an Embedded Program or embedded Erase

algorithm. Table 12 shows the address and data re-

quirements for both command sequences. See also

Secured Silicon Sector Flash Memory Region for fur-

ther information. Note that the ACC function and

unlock bypass modes are not available when the Se-

cured Silicon Sector is enabled.

Byte/Word Program Command Sequence

The system may program the device by word or byte,

depending on the state of the BYTE# pin. Program-

ming is a four-bus-cycle operation. The program

command sequence is initiated by writing two unlock

write cycles, followed by the program set-up com-

mand. The program address and data are written next,

which in turn initiate the Embedded Program algo-

rithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 12 shows the address

and data requirements for the byte program command

sequence. Note that the Secured Silicon Sector, au-

toselect, and CFI functions are unavailable when a

program operation in is progress.

When the Embedded Program algorithm is complete,

that bank then returns to the read mode and ad-

dresses are no longer latched. The system can

determine the status of the program operation by

using DQ7, DQ6, or RY/BY#. Refer to the Write Oper-

ation Status section for information on these status

bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program

operation. The program command sequence should

be reinitiated once that bank has returned to the read

mode, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from “0” back to a “1.” Attempting to do so may

cause that bank to set DQ5 = 1, or cause the DQ7 and

DQ6 status bits to indicate the operation was success-

ful. However, a succeeding read shows that the data is

still “0.” Only erase operations can convert a “0” to a

“1.”

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes or words to a bank faster than using the

standard program command sequence. The unlock

bypass command sequence is initiated by first writing

two unlock cycles. This is followed by a third write

cycle containing the unlock bypass command, 20h.

That bank then enters the unlock bypass mode. A

two-cycle unlock bypass program command sequence

is all that is required to program in this mode. The first

cycle in this sequence contains the unlock bypass pro-

gram command, A0h; the second cycle contains the

program address and data. Additional data is pro-

grammed in the same manner. This mode dispenses

with the initial two unlock cycles required in the stan-

dard program command sequence, resulting in faster

total programming time. Table 12 shows the require-

ments for the command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. (See Table 12).

The device offers accelerated program operations

through the WP#/ACC pin. When the system asserts

VHH on the WP#/ACC pin, the device automatically en-

ters the Unlock Bypass mode. The system may then

write the two-cycle Unlock Bypass program command

sequence. The device uses the higher voltage on the

WP#/ACC pin to accelerate the operation. Note that

the WP#/ACC pin must not be at VHH any operation

other than accelerated programming, or device dam-

age may result. In addition, the WP#/ACC pin must not

be left floating or unconnected; inconsistent behavior

of the device may result.

Figure 4 illustrates the algorithm for the program oper-

ation. Refer to the Erase and Program Operations

table in the AC Characteristics section for parameters,

and Figure 18 for timing diagrams.

D640D90VF 数据表(PDF) 26 Page - Advanced Micro Devices

D640D90VF 数据表(HTML) 26 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

数据表下载