PPC440SPE-RNB667C datasheet(51/80 Pages) AMCC

51 / 80 page

PowerPC 440SPe Embedded Processor

Revision 1.23 - Sept 21, 2006

AMCC Proprietary

Preliminary Data Sheet

PCIX0Clk

Input PCI & PCI-X Clock.

Note:If the PCI-X interface is not being used, drive this

pin with a 3.3V clock signal at a frequency

between 1 and 66MHz

3.3V PCI

PCIX0DevSel

Indicates the driving device has decoded its address as

the target of the current access.

I/O

3.3V PCI

PCIX0ECC5:2

ECC check bits 5–2. All ECC bits are valid only for PCIX

DDR mode 2.

Note:See PCIXPar for ECC0.

See PCIXAck64 for ECC1.

See PCIXReq64 for ECC6.

See PCIXPar64 for ECC7.

I/O

3.3V PCI or

1.5V PCI for

mode 2

PCIX0Frame

Driven by the current master to indicate beginning and

duration of an access.

I/O

3.3V PCI

PCIX0Gnt0

PCIX0Gnt1:3

Indicates that the specified agent is granted access to

the PCI-X bus. When Arbitration is internal to the

PPC440SPe, all GRANTS Gnt0:3 are outputs. When

arbitration is external, only Gnt 0 is used as an Input.

I/O

3.3V PCI

PCIX0IDSel

Used as a chip select during configuration read and

write transactions. If the PCI-X is a Host, during

Configuration the ISDSEL is an Output that duplicates

the AD17. The ISDSEL is always 3.3V even in Mode 2

DDR

I/O

3.3V PCI

PCIX0INTA

Level sensitive PCI interrupt.

3.3V PCI

PCIX0IRDY

Indicates initiating agent’s ability to complete the current

data phase of the transaction.

I/O

3.3V PCI

PCIX0M66En

Capable of 66MHz operation.

3.3V PCI or

1.5V PCI for

mode 2

PCIX0Par/PCIX0ECC0

Even parity indicator or ECC0.

Normally used to indicate even parity across

PCIAD31:00 and BE3:0.

Used as ECC0 for PCIX0 mode 2.

I/O

3.3V PCI or

1.5V PCI for

mode 2

PCIX0Par64/PCIX0ECC7

Even parity indicator or ECC7.

Normally used to indicate even parity across

PCIXAD63:32 and BE7:4 for PCIX0

Used as ECC7 for PCIX0 mode 2.

I/O

3.3V PCI or

1.5V PCI for

mode 2

PCIX0PErr

Reports data parity errors during all PCI transactions

except a Special Cycle.

I/O

3.3V PCI

PCIX0Req0

PCIX0Req1:3

An indication to the PCI-X arbiter that the specified

agent wishes to use the bus.

When Arbitration is internal to the PPC440SPe, all

REQS Req0:3 are Inputs. When arbitration is external,

only Req 0 is used as an output.

I/O

3.3V PCI

Table 6. Signal Functional Description (Sheet 2 of 8)

Notes:

1. Receiver input has hysteresis

2. Must pull up (recommended value is 3k

Ω to 3.3V)

3. Must pull down (recommended value is 1k

Ω)

4. If not used, must pull up (recommended value is 3k

Ω to 3.3V)

5. If not used, must pull down (recommended value is 1k

Ω)

6. Strapping input during reset; pull-up or pull-down required

Signal Name

Description

I/O

Type

Notes

PPC440SPE-RNB667C 数据表(PDF) 51 Page - Applied Micro Circuits Corporation

PPC440SPE-RNB667C 数据表(HTML) 51 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载

链接网址

PPC440SPE-RNB667C 数据表(PDF) 51 Page - Applied Micro Circuits Corporation

PPC440SPE-RNB667C 数据表(HTML) 51 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表 下载

链接网址

数据表下载