| 数据搜索系统,热门电子元器件搜索 |
|
PPC440SPE-RNB667C 数据表(PDF) 54 Page - Applied Micro Circuits Corporation |
|
|
|||||||||||||||||||||||||||||
PPC440SPE-RNB667C 数据表(HTML) 54 Page - Applied Micro Circuits Corporation |
|
54 / 80 page ![]() PowerPC 440SPe Embedded Processor 54 AMCC Proprietary Revision 1.23 - Sept 21, 2006 Preliminary Data Sheet External Slave Peripheral Interface - EBC PerAddr00:26 Peripheral address bus. Note:PerAddr00 is the most significant bit (msb). O3.3V LVTTL 1 PerBE0:1 External peripheral data bus byte enable. O 3.3V LVTTL 1 PerBLast Used by the peripheral controller to indicates the last transfer of a memory access. O3.3V LVTTL PerCS0:2 External peripheral device select. O 3.3V LVTTL PerData00:15 Peripheral data bus. Note:PerData0 is the most significant bit (msb). I/O 3.3V LVTTL 1 PerOE Used by peripheral controller or DMA controller depending upon the type of transfer involved. When the PPC440SPe is the bus master, it enables the selected device to drive the bus. O3.3V LVTTL PerPar0:1 External peripheral data bus byte parity. I/O 3.3V LVTTL 1 PerReady Used by a peripheral slave to indicate it is ready to transfer data. I3.3V LVTTL PerR/W The peripheral controller set this signal to High for a Read from external memory, and to Low for a Write. O3.3V LVTTL 1 PerWE Write Enable. O 3.3V LVTTL PerClk Peripheral clock used by synchronous peripheral slaves. O 3.3V LVTTL PerErr External error used as an input to record external slave peripheral errors. I 3.3V LVTTL 1, 5 IIC Peripheral Interface IIC0SClk IIC0 Serial Clock. I/O 3.3V IIC 1, 2 IIC0SDA IIC0 Serial Data. I/O 3.3V IIC 1, 2 IIC1SClk IIC1 Serial Clock. I/O 3.3V IIC 1, 2 IIC1SDA IIC1 Serial Data. I/O 3.3V IIC 1, 2 Table 6. Signal Functional Description (Sheet 5 of 8) Notes: 1. Receiver input has hysteresis 2. Must pull up (recommended value is 3k Ω to 3.3V) 3. Must pull down (recommended value is 1k Ω) 4. If not used, must pull up (recommended value is 3k Ω to 3.3V) 5. If not used, must pull down (recommended value is 1k Ω) 6. Strapping input during reset; pull-up or pull-down required Signal Name Description I/O Type Notes |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |