21

SETPOINT SELECTIONS



- Select main or alternate setpoints



- Reset Setpoint 1 (Alarm 1)



- Reset Setpoint 2 (Alarm 2)



- Reset Setpoint 3 (Alarm 3)



- Reset Setpoint 4 (Alarm 4)



- Reset Setpoint 3 & 4 (Alarm 3 & 4)



- Reset Setpoint 2, 3 & 4 (Alarm 2, 3 & 4)



- Reset Setpoint All (Alarm All)

The following selections are accessible only with the Setpoint option card

installed. Refer to Module 6 for an explanation of their operation.

Setpoint

Card

Only

















PRINT REQUEST

The meter issues a block print through the serial port when activated. The

data transmitted during a print request is programmed in Module 7. If the user

input is still active after the transmission is complete (about 100 msec), an

additional transmission occurs. As long as the user input is held active,

continuous transmissions occur.









PROGRAM MODE SECURITY CODE*

By entering any non-zero value, the prompt   will appear when trying

to access the Program Mode. Access will only be allowed after entering a

matching security code or universal code of . With this lock-out, a user input

would not have to be configured for Program Lock-out. However, this lock-out

is overridden by an inactive user input configured for Program Lock-out.

































SP-1 SP-2 SP-3 SP-4 SETPOINT ACCESS*

The setpoint displays can be programmed for ,  or  (See the

following table). Accessible only with the Setpoint option card installed.

























MAXIMUM DISPLAY LOCK-OUT*

MINIMUM DISPLAY LOCK-OUT*

TOTALIZER DISPLAY LOCK-OUT*

These displays can be programmed for  or . When programmed for



, the display will not be shown when the

DSP key is pressed regardless of

Program Lock-out status. It is suggested to lock-out the display if it is not needed.

The associated function will continue to operate even if its display is locked-out.

3-LOC

LO

HI

tOt

SP-1

SP-2

CodE

PAR

Pro

Min Display

Lock-out

Max Display

Lock-out

Total Display

Lock-out

Setpoint 1

Access

Security

Code

Setpoint 2

Access

SP-3

Setpoint 3

Access

SP-4

Setpoint 4

Access

6.3 mOdUle 3 - display and prOgram lOCK-OUT

parameTers ()

PARAMETER MENU

* Factory Setting can be used without affecting basic start-up.



to 

Module 3 is the programming for Display lock-out and “Full” and “Quick”

Program lock-out.

When in the Display Mode, the available displays can be read consecutively

by repeatedly pressing the

DSP key. An annunciator indicates the display being

shown. These displays can be locked from being visible. It is recommended that

the display be set to  when the corresponding function is not used.

“Full” Programming Mode permits all parameters to be viewed and

modified. This Programming Mode can be locked with a security code and/or

user input. When locked and the

PAR key is pressed, the meter enters a Quick

Programming Mode. In this mode, the setpoint values can still be read and/or

changed per the selections below. The Display Intensity Level ()

parameter also appears whenever Quick Programming Mode is enabled and the

security code is greater than zero.







SELECTION

DESCRIPTION

Visible but not changeable in Quick Programming Mode

Visible and changeable in Quick Programming Mode

Not visible in Quick Programming Mode

Immediate access.

“Full” Programming

Not Active



0

No access

Quick Programming

Active



0

Immediate access.

“Full” Programming

Not Active



>0

After Quick Programming with correct code # at  prompt.

Quick Programming w/Display Intensity

Active



>0

After Quick Programming with correct code # at  prompt.

Quick Programming w/Display Intensity

————

not 

>0

Immediate access.

“Full” Programming

————

not 

0

“FULL” PROGRAMMING MODE ACCESS

WHEN PAR KEY IS

PRESSED

USER INPUT

STATE

USER INPUT

CONFIGURED

SECURITY

CODE

PROGRAMMING MODE ACCESS

Throughout this document, Programming Mode (without Quick in front) always refers to “Full” Programming (all meter parameters are accessible).

SELECTION DESCRIPTION



Visible in Display Mode



Not visible in Display Mode

ì

í

î