LP85571 datasheet(35/49 Pages) TI2

35 / 49 page

OUT

efficiency

2 L

´ ´

OUT

PEAK

OUT

2 I

efficiency)

L efficien

OUT

PEAK

OUT

efficiency

x 1

efficiency

LP8557, LP85571

www.ti.com

SNVSA15B – DECEMBER 2013 – REVISED DECEMBER 2015

9.2.1.2 Detailed Design Procedure

9.2.1.2.1

Boost Output Capacitor Selection

The LP8557 inductive boost converter typically requires two 4.7-µF output capacitors. The voltage rating of the

capacitor must be 35 V or higher as the OVP threshold is at 29.6 V (typ). Pay careful attention to the capacitor

tolerance and DC bias response. For proper operation the degradation in capacitance due to tolerance, DC bias,

and temperature should stay above 2 µF. This might require placing more than two devices in parallel in order to

maintain the required output capacitance over the device operating temperature and output voltage range.

9.2.1.2.2

Schottky Diode Selection

The Schottky diode must have a reverse breakdown voltage greater than the LP8557’s maximum output voltage.

Additionally, the diode must have an average current rating high enough to handle the LP8557 maximum output

current; at the same time the diode's peak current rating must be high enough to handle the peak inductor

current. Schottky diodes are required due to their lower forward voltage drop (0.3V to 0.5V) and their fast

recovery time.

9.2.1.2.3

Inductor Selection

The chosen inductor must be from 10 to 22 µH (for 500-kHz operation) or 4.7 to 10 µH (for 1-MHz operation) and

must have a saturation rating equal to, or greater than, the circuit's peak operating current. IPEAK can be found by

the following calculation:

(1)

This assumes the device is operating in continuous conduction mode (CCM) which is typically the case when

operating near the peak current. For smaller rated inductors, and when the device is operating in discontinuous

conduction mode (DCM), the peak current can be found from:

(2)

The device operates in CCM when the following is true:

(3)

9.2.1.2.4

Boost Input andVDD Capacitor Selection

The LP8557 VDD pin is typically tied to the same supply as the input of the boost power stage (VIN node). A 10-

µF input capacitor is recommended on that node. The voltage rating of the capacitor must be at least 10 V. If a

supply powering the VDD pin is different from a supply powering the boost power stage, then 10-µF input

capacitors are required on both VDD and VIN nodes.

Submit Documentation Feedback

Product Folder Links: LP8557 LP85571

LP85571 数据表(PDF) 35 Page - Texas Instruments

LP85571 数据表(HTML) 35 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

数据表下载

链接网址

LP85571 数据表(PDF) 35 Page - Texas Instruments

LP85571 数据表(HTML) 35 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

数据表 下载

链接网址

数据表下载