 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
MPC855T 数据表(PDF) 20 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC855T 数据表(HTML) 20 Page - Freescale Semiconductor, Inc |
|
|
20 / 80 page  MPC860 PowerQUICC™ Family Hardware Specifications, Rev. 8 20 Freescale Semiconductor Bus Signal Timing B35 A(0:31), BADDR(28:30) to CS valid—as requested by control bit BST4 in the corresponding word in UPM 5.58 — 4.25 — 3.00 — 1.79 — ns B35a A(0:31), BADDR(28:30), and D(0:31) to BS valid—as requested by control bit BST1 in the corresponding word in UPM 13.15 — 10.50 — 8.00 — 5.58 — ns B35b A(0:31), BADDR(28:30), and D(0:31) to BS valid—as requested by control bit BST2 in the corresponding word in UPM 20.73 — 16.75 — 13.00 — 9.36 — ns B36 A(0:31), BADDR(28:30), and D(0:31) to GPL valid—as requested by control bit GxT4 in the corresponding word in UPM 5.58 — 4.25 — 3.00 — 1.79 — ns B37 UPWAIT valid to CLKOUT falling edge9 6.00 — 6.00 — 6.00 — 6.00 — ns B38 CLKOUT falling edge to UPWAIT valid9 1.00 — 1.00 — 1.00 — 1.00 — ns B39 AS valid to CLKOUT rising edge10 7.00 — 7.00 — 7.00 — 7.00 — ns B40 A(0:31), TSIZ(0:1), RD/WR, BURST, valid to CLKOUT rising edge 7.00 — 7.00 — 7.00 — 7.00 — ns B41 TS valid to CLKOUT rising edge (setup time) 7.00 — 7.00 — 7.00 — 7.00 — ns B42 CLKOUT rising edge to TS valid (hold time) 2.00 — 2.00 — 2.00 — 2.00 — ns B43 AS negation to memory controller signals negation —TBD —TBD —TBD —TBD ns 1 Phase and frequency jitter performance results are only valid if the input jitter is less than the prescribed value. 2 If the rate of change of the frequency of EXTAL is slow (that is, it does not jump between the minimum and maximum values in one cycle) or the frequency of the jitter is fast (that is, it does not stay at an extreme value for a long time) then the maximum allowed jitter on EXTAL can be up to 2%. 3 The timings specified in B4 and B5 are based on full strength clock. 4 The timing for BR output is relevant when the MPC860 is selected to work with external bus arbiter. The timing for BG output is relevant when the MPC860 is selected to work with internal bus arbiter. 5 The timing required for BR input is relevant when the MPC860 is selected to work with internal bus arbiter. The timing for BG input is relevant when the MPC860 is selected to work with external bus arbiter. 6 The D(0:31) and DP(0:3) input timings B18 and B19 refer to the rising edge of the CLKOUT in which the TA input signal is asserted. 7 The D(0:31) and DP(0:3) input timings B20 and B21 refer to the falling edge of the CLKOUT. This timing is valid only for read accesses controlled by chip-selects under control of the UPM in the memory controller, for data beats where DLT3 = 1 in the UPM RAM words. (This is only the case where data is latched on the falling edge of CLKOUT.) 8 The timing B30 refers to CS when ACS = 00 and to WE(0:3) when CSNT = 0. 9 The signal UPWAIT is considered asynchronous to the CLKOUT and synchronized internally. The timings specified in B37 and B38 are specified to enable the freeze of the UPM output signals as described in Figure 18. 10 The AS signal is considered asynchronous to the CLKOUT. The timing B39 is specified in order to allow the behavior specified in Figure 21. Table 7. Bus Operation Timings (continued) Num Characteristic 33 MHz 40 MHz 50 MHz 66 MHz Unit Min Max Min Max Min Max Min Max |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
