ST7LITE3XF2 datasheet(67/173 Pages) STMICROELECTRONICS

67 / 173 page

ST7LITE3xF2

67/173

DUAL 12-BIT AUTORELOAD TIMER 3 (Cont’d)

11.2.6 Register Description

TIMER CONTROL STATUS REGISTER

(ATCSR)

Read / Write

Reset Value: 0x00 0000 (x0h)

Bit 7 = Reserved.

Bit 6 = ICF Input Capture Flag.

This bit is set by hardware and cleared by software

by reading the ATICR register (a read access to

ATICRH or ATICRL will clear this flag). Writing to

this bit does not change the bit value.

0: No input capture

1: An input capture has occurred

Bit 5 = ICIE IC Interrupt Enable.

This bit is set and cleared by software.

0: Input capture interrupt disabled

1: Input capture interrupt enabled

Bits 4:3 = CK[1:0] Counter Clock Selection.

These bits are set and cleared by software and

cleared by hardware after a reset. They select the

clock frequency of the counter.

Bit 2 = OVF1 Overflow Flag.

This bit is set by hardware and cleared by software

by reading the TCSR register. It indicates the tran-

sition of the counter1 CNTR1 from FFh to ATR1

value.

0: No counter overflow occurred

1: Counter overflow occurred

Bit 1 = OVFIE1 Overflow Interrupt Enable.

This bit is read/write by software and cleared by

hardware after a reset.

0: Overflow interrupt disabled.

1: Overflow interrupt enabled.

Bit 0 = CMPIE Compare Interrupt Enable.

This bit is read/write by software and cleared by

hardware after a reset. It can be used to mask the

interrupt generated when any of the CMPFx bit is

set.

0: Output compare interrupt disabled.

1: Output Compare interrupt enabled.

COUNTER REGISTER 1 HIGH (CNTR1H)

Read only

Reset Value: 0000 0000 (000h)

COUNTER REGISTER 1 LOW (CNTR1L)

Read only

Reset Value: 0000 0000 (000h)

Bits 15:12 = Reserved.

Bits 11:0 = CNTR1[11:0] Counter Value.

This 12-bit register is read by software and cleared

by hardware after a reset. The counter CNTR1 is

incremented continuously as soon as a counter

clock is selected. To obtain the 12-bit value, soft-

ware should read the counter value in two consec-

utive read operations. The CNTR1H register can

be incremented between the two reads, and in or-

der to be accurate when fTIMER=fCPU, the software

should take this into account when CNTR1L and

CNTR1H are read. If CNTR1L is close to its high-

est value, CNTR1H could be incremented before it

is read.

When a counter overflow occurs, the counter re-

starts from the value specified in the ATR1 regis-

ter.

ICF

ICIE

CK1

CK0

OVF1 OVFIE1 CMPIE

Counter Clock Selection

CK1

CK0

OFF

fLTIMER (1 ms timebase @ 8 MHz)

fCPU

000

CNTR1_

ST7LITE3XF2 数据表(PDF) 67 Page - STMicroelectronics

ST7LITE3XF2 数据表(HTML) 67 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载