STR730FZ1T7 datasheet(22/52 Pages) STMICROELECTRONICS

22 / 52 page

Electrical parameters

STR73xFxx

22/52

4.2

Absolute maximum ratings

Stresses above those listed as “absolute maximum ratings” may cause permanent damage

to the device. This is a stress rating only and functional operation of the device under these

conditions is not implied. Exposure to maximum rating conditions for extended periods may

affect device reliability.

All 5 V power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external 5 V

supply

IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum

cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive

injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS.

Negative injection disturbs the analog performance of the device. See note in Section 4.3.6: 10-bit ADC

characteristics on page 43.

When several inputs are submitted to a current injection, the maximum

ΣI

INJ(PIN) is the absolute sum of the

positive and negative injected currents (instantaneous values). These results are based on

characterization with

ΣI

INJ(PIN) maximum current injection on four I/O port pins of the device.

5.) In 144-pin devices, only +10 mA on P0.3, P1.13, P3.6 and P4.13 pins (negative injection not allowed).

Table 5.

Voltage characteristics

Symbol

Ratings

Min

Max

Unit

VDD - VSS

External 5 V Supply voltage

-0.3

6.0

VSSA

Reference ground for A/D converter

VSS

VDDA- VSSA

Reference voltage for A/D converter

-0.3

VDD+0.3

VIN

Input voltage on any pin

-0.3

VDD+0.3

ΔV

DDx|

Variations between different 5 V

power pins

-0.3

|VSSX - VSS|

Variations between all the different

ground pins

-0.3

VESD(HBM)

Electrostatic discharge voltage

(Human Body Model)

see : Absolute maximum ratings

(electrical sensitivity) on page 36

VESD(MM)

Electrostatic discharge voltage

(Machine Model)

Table 6.

Current characteristics

Symbol

Ratings

Max.

Unit

IVDD

Total current into VDD power lines (source)

100

IVSS

Total current out of VSS ground lines (sink)

100

IIO

Output current sunk by any I/O and control pin

Output current source by any I/O and control pin

IINJ(PIN)

2) & 3)

Injected current on any other pin 4) &5)

±10

ΣI

INJ(PIN)

Total injected current (sum of all I/O and control pins) 4)

±75

STR730FZ1T7 数据表(PDF) 22 Page - STMicroelectronics

STR730FZ1T7 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载

链接网址

STR730FZ1T7 数据表(PDF) 22 Page - STMicroelectronics

STR730FZ1T7 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表 下载

链接网址

数据表下载