T80C5112-RKSIL datasheet(51/97 Pages) ATMEL

51 / 97 page

Rev. B - November 10, 2000

Preliminary

T80C5112

The CMOD SFR includes three additional bits associated with the PCA (See Figure 22 and Table 26).

· The CIDL bit which allows the PCA to stop during idle mode.

· The WDTE bit which enables or disables the watchdog function on module 4.

· The ECF bit which when set causes an interrupt and the PCA overflow flag CF (in the CCON SFR) to be set

when the PCA timer overflows.

The CCON SFR contains the run control bit for the PCA and the flags for the PCA timer (CF) and each module

(Refer to Table 27).

· Bit CR (CCON.6) must be set by software to run the PCA. The PCA is shut off by clearing this bit.

· Bit CF: The CF bit (CCON.7) is set when the PCA counter overflows and an interrupt will be generated if the

ECF bit in the CMOD register is set. The CF bit can only be cleared by software.

· Bits 0 through 4 are the flags for the modules (bit 0 for module 0, bit 1 for module 1, etc.) and are set by

hardware when either a match or a capture occurs. These flags also can only be cleared by software.

Table 27. CCON: PCA Counter Control Register

The watchdog timer function is implemented in module 4 (See Figure 25).

The PCA interrupt system is shown in Figure 23

CCON

Address 0D8H

CCF4

CCF3

CCF2

CCF1

CCF0

Reset value

Symbol

Function

PCA Counter Overflow flag. Set by hardware when the counter rolls over. CF flags

an interrupt if bit ECF in CMOD is set. CF may be set by either hardware or software but

can only be cleared by software.

PCA Counter Run control bit. Set by software to turn the PCA counter on. Must be cleared

by software to turn the PCA counter off.

Not implemented, reserved for future use.a

User software should not write 1s to reserved bits. These bits may be used in future 8051 family

products to invoke new features. In that case, the reset or inactive value of the new bit will be 0, and its

active value will be 1. The value read from a reserved bit is indeterminate.

CCF4

PCA Module 4 interrupt flag. Set by hardware when a match or capture occurs. Must be

cleared by software.

CCF3

PCA Module 3 interrupt flag. Set by hardware when a match or capture occurs. Must be

cleared by software.

CCF2

PCA Module 2 interrupt flag. Set by hardware when a match or capture occurs. Must be

cleared by software.

CCF1

PCA Module 1 interrupt flag. Set by hardware when a match or capture occurs. Must be

cleared by software.

CCF0

PCA Module 0 interrupt flag. Set by hardware when a match or capture occurs. Must be

cleared by software.

T80C5112-RKSIL 数据表(PDF) 51 Page - ATMEL Corporation

T80C5112-RKSIL 数据表(HTML) 51 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

数据表下载

链接网址

T80C5112-RKSIL 数据表(PDF) 51 Page - ATMEL Corporation

T80C5112-RKSIL 数据表(HTML) 51 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

数据表 下载

链接网址

数据表下载