STM32F107VB datasheet(19/95 Pages) STMICROELECTRONICS

19 / 95 page

STM32F105xx, STM32F107xx

Description

Doc ID 15274 Rev 4

19/95

USART1, USART2 and USART3 also provide hardware management of the CTS and RTS

signals, Smart Card mode (ISO 7816 compliant) and SPI-like communication capability. All

interfaces can be served by the DMA controller except for UART5.

2.3.18

Serial peripheral interface (SPI)

Up to three SPIs are able to communicate up to 18 Mbits/s in slave and master modes in

full-duplex and simplex communication modes. The 3-bit prescaler gives 8 master mode

frequencies and the frame is configurable to 8 bits or 16 bits. The hardware CRC

generation/verification supports basic SD Card/MMC/SDHC(a) modes.

All SPIs can be served by the DMA controller.

2.3.19

Inter-integrated sound (I2S)

Two standard I2S interfaces (multiplexed with SPI2 and SPI3) are available, that can be

operated in master or slave mode. These interfaces can be configured to operate with 16/32

bit resolution, as input or output channels. Audio sampling frequencies from 8 kHz up to

96 kHz are supported. When either or both of the I2S interfaces is/are configured in master

mode, the master clock can be output to the external DAC/CODEC at 256 times the

sampling frequency with less than 0.5% accuracy error owing to the advanced clock

controller (see Section 2.3.7: Clocks and startup).

Please refer to the “Audio frequency precision” tables provided in the “Serial peripheral

interface (SPI)” section of the STM32F10xxx reference manual.

2.3.20

Ethernet MAC interface with dedicated DMA and IEEE 1588 support

Peripheral not available on STM32F105xx devices.

The STM32F107xx devices provide an IEEE-802.3-2002-compliant media access controller

(MAC) for ethernet LAN communications through an industry-standard media-independent

interface (MII) or a reduced media-independent interface (RMII). The STM32F107xx

requires an external physical interface device (PHY) to connect to the physical LAN bus

(twisted-pair, fiber, etc.). the PHY is connected to the STM32F107xx MII port using as many

as 17 signals (MII) or 9 signals (RMII) and can be clocked using the 25 MHz (MII) or 50 MHz

(RMII) output from the STM32F107xx.

The STM32F107xx includes the following features:

Supports 10 and 100 Mbit/s rates

Dedicated DMA controller allowing high-speed transfers between the dedicated SRAM

and the descriptors (see the STM32F105xx/STM32F107xx reference manual for

details)

Tagged MAC frame support (VLAN support)

Half-duplex (CSMA/CD) and full-duplex operation

MAC control sublayer (control frames) support

a. SDHC = Secure digital high capacity.

STM32F107VB 数据表(PDF) 19 Page - STMicroelectronics

STM32F107VB 数据表(HTML) 19 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

数据表下载