CC2420-RTR1 datasheet(30/92 Pages) TI

30 / 92 page

CC2420

SWRS041B

Page 30 of 89

divided into three memory banks: TXFIFO

(bank 0), RXFIFO (bank 1) and security

(bank 2). The FIFO banks are 128 bytes

each, while the security bank is 112 bytes.

A6:0 is transmitted directly after the

RAM/Register bit as shown in Figure 9.

For RAM access, a second byte is also

required before the data transfer. This

byte contains B1:0 in bits 7 and 6,

followed by the R/W bit (0 for read+write, 1

for read). Bits 4 through 0 are don’t care

as shown in Figure 9.

For RAM write, data to be written must be

input on the SI pin directly after the

second address byte. RAM data read is

output on the SO pin simultaneously, but

may be ignored by the user if only writing

is of interest.

For RAM read, the selected byte(s) are

output on the SO pin directly after the

second address byte.

See Figure 10 for an illustration on how

multiple RAM bytes may be read or written

in one operation.

The RAM memory space is shown in

Table 6. The lower 256 bytes are used to

store FIFO data. Note that RAM access

should never be used for FIFO write

operations because the FIFO counter will

not be updated. Use RXFIFO and TXFIFO

access instead as described in section

FIFO access.

As with register data, data stored in RAM

will be retained during power down mode,

but not when the power-supply is turned

off (e.g. by disabling the voltage regulator

using the VREG_EN pin).

ADDR

CSn:

Command strobe:

Read or write a whole register (16 bit):

DATA

8MSB

ADDR

DATA

8LSB

Read 8 MSB of a register:

DATA

8MSB

ADDR

Multiple register read or write

DATA

8MSB

ADDR

DATA

8LSB

DATA

8MSB

DATA

8LSB

...

Read or write n bytes from/to RF FIFO:

DATA

byte0

ADDR

FIFO

DATA

byte1

DATA

byte2

DATA

byte3

DATA

byte n-2 DATAbyte n-1

...

ADDR

Multiple command strobes:

ADDR

...

ADDR

DATA

8MSB

ADDR

DATA

byte n-3

ADDR

...

Read or write n bytes from/to RAM:

ADDRH

RAM

ADDRL

RAM

DATA

ADDR

DATA

ADDR+1 DATAADDR+2

DATA

ADDR+n

...

FIFO and RAM access must be terminated with setting the CSn pin high.

Command strobes and register access may be followed by any other access,

since they are completed on the last negative edge on SCLK. They may however also be

terminated with setting CSn high, if desirable, e.g. for reading only 8 bits from a configuration

Note:

Figure 10. Configuration registers write and read operations via SPI

CC2420-RTR1 数据表(PDF) 30 Page - Texas Instruments

CC2420-RTR1 数据表(HTML) 30 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

数据表下载

链接网址

CC2420-RTR1 数据表(PDF) 30 Page - Texas Instruments

CC2420-RTR1 数据表(HTML) 30 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

数据表 下载

链接网址

数据表下载