ADM1275-2ARQZ-R7 datasheet(9/48 Pages) AD

9 / 48 page

Data Sheet

ADM1275

Rev. D | Page 9 of 48

PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

VCAP

TIMER

ISET

VCC

SENSE–

GATE

GND

PWRGD

FLB

VOUT

GPO1/ALERT1/CONV

ADR

LATCH

GPO2/ALERT2

SDA

SCL

SENSE+

ADM1275-1

TOP VIEW

(Not to Scale)

Figure 3. ADM1275-1 Pin Configuration, QSOP

VCAP

ISET

TIMER

NOTES

1. SOLDER THE EXPOSED PADDLE TO

THE BOARD TO IMPROVE THERMAL

DISSIPATION. THE EXPOSED PADDLE

CAN BE CONNECTED TO GROUND.

FLB

VOUT

GND

PWRGD

SCL

ADM1275-1

TOP VIEW

(Not to Scale)

PIN 1

INDICATOR

Figure 4. ADM1275-1 Pin Configuration, LFCSP

Table 5. ADM1275-1 Pin Function Descriptions

Pin No.

QSOP

LFCSP

Mnemonic

Description

VCC

Positive Supply Input Pin. An undervoltage lockout (UVLO) circuit resets the device when a low

supply voltage is detected. GATE is held low when the supply is below UVLO. During normal

operation, this pin should remain greater than or equal to SENSE+ to ensure that specifications

are adhered to. No sequencing is required.

Undervoltage Input Pin. An external resistor divider is used from the supply to this pin to allow an

internal comparator to detect whether the supply is under the UV limit.

Overvoltage Input Pin. An external resistor divider is used from the supply to this pin to allow an

internal comparator to detect whether the supply is above the OV limit.

VCAP

Internal Regulated Supply. A capacitor with a value of 1 µF or greater should be placed on this pin

to maintain good accuracy. This pin can be used as a reference to program the ISET pin voltage.

ISET

This pin allows the current limit threshold to be programmed. The default limit is set when this pin

is connected directly to VCAP. To achieve a user-defined sense voltage, the current limit can be

adjusted using a resistor divider from VCAP. An external reference can also be used.

Soft Start Pin. A capacitor is used on this pin to set the soft start ramp profile. The voltage on the

SS pin controls the current sense voltage limit, which controls the inrush current profile.

TIMER

Timer Pin. An external capacitor, CTIMER, sets an initial timing cycle delay and a fault delay. The GATE

pin is pulled low when the voltage on the TIMER pin exceeds the upper threshold.

LATCH

Signals that the device is latching off after an overcurrent fault. The device can be configured for

automatic retry after latch-off by connecting this pin directly back to the UV pin.

ADR

PMBus Address Pin. This pin can be tied to GND, tied to VCAP, left floating, or tied low through a

resistor to set four different PMBus addresses (see the Device Addressing section).

GPO1/ALERT1/

CONV

General-Purpose Digital Output (GPO1).

Alert (ALERT1). This pin can be configured to generate an alert signal when one or more fault or

warning conditions are detected.

Conversion (CONV). This pin can be used as an input signal to control when a power monitor ADC

sampling cycle begins.

At power-up, this pin defaults to a high impedance state. There is no internal pull-up on this pin.

GPO2/ALERT2

General-Purpose Digital Output (GPO2).

Alert (ALERT2). This pin can be configured to generate an alert signal when one or more fault or

warning conditions are detected.

At power-up, this pin indicates the FET health mode by default. There is no internal pull-up on this pin.

ADM1275-2ARQZ-R7 数据表(PDF) 9 Page - Analog Devices

ADM1275-2ARQZ-R7 数据表(HTML) 9 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载

链接网址

ADM1275-2ARQZ-R7 数据表(PDF) 9 Page - Analog Devices

ADM1275-2ARQZ-R7 数据表(HTML) 9 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表 下载

链接网址

数据表下载