STM32F415VG datasheet(23/186 Pages) STMICROELECTRONICS

23 / 186 page

DocID022063 Rev 4

23/186

STM32F415xx, STM32F417xx

Description

event (rising edge, falling edge, both) and can be masked independently. A pending register

maintains the status of the interrupt requests. The EXTI can detect an external line with a

pulse width shorter than the Internal APB2 clock period. Up to 140 GPIOs can be connected

to the 16 external interrupt lines.

2.2.12

Clocks and startup

On reset the 16 MHz internal RC oscillator is selected as the default CPU clock. The

16 MHz internal RC oscillator is factory-trimmed to offer 1% accuracy over the full

temperature range. The application can then select as system clock either the RC oscillator

or an external 4-26 MHz clock source. This clock can be monitored for failure. If a failure is

detected, the system automatically switches back to the internal RC oscillator and a

software interrupt is generated (if enabled). This clock source is input to a PLL thus allowing

to increase the frequency up to 168 MHz. Similarly, full interrupt management of the PLL

clock entry is available when necessary (for example if an indirectly used external oscillator

fails).

Several prescalers allow the configuration of the three AHB buses, the high-speed APB

(APB2) and the low-speed APB (APB1) domains. The maximum frequency of the three AHB

buses is 168 MHz while the maximum frequency of the high-speed APB domains is

84 MHz. The maximum allowed frequency of the low-speed APB domain is 42 MHz.

The devices embed a dedicated PLL (PLLI2S) which allows to achieve audio class

performance. In this case, the I2S master clock can generate all standard sampling

frequencies from 8 kHz to 192 kHz.

2.2.13

Boot modes

At startup, boot pins are used to select one out of three boot options:

•

Boot from user Flash

•

Boot from system memory

•

Boot from embedded SRAM

The boot loader is located in system memory. It is used to reprogram the Flash memory by

using USART1 (PA9/PA10), USART3 (PC10/PC11 or PB10/PB11), CAN2 (PB5/PB13), USB

OTG FS in Device mode (PA11/PA12) through DFU (device firmware upgrade).

2.2.14

Power supply schemes

•

VDD = 1.8 to 3.6 V: external power supply for I/Os and the internal regulator (when

enabled), provided externally through VDD pins.

•

VSSA, VDDA = 1.8 to 3.6 V: external analog power supplies for ADC, DAC, Reset

blocks, RCs and PLL. VDDA and VSSA must be connected to VDD and VSS, respectively.

•

VBAT = 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and

backup registers (through power switch) when VDD is not present.

Refer to Figure 21: Power supply scheme for more details.

Note:

VDD/VDDA minimum value of 1.7 V is obtained when the device operates in reduced

temperature range, and with the use of an external power supply supervisor (refer to

Section : Internal reset OFF).

Refer to Table 2 in order to identify the packages supporting this option.

STM32F415VG 数据表(PDF) 23 Page - STMicroelectronics

STM32F415VG 数据表(HTML) 23 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载