数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

AN2156 数据表(PDF) 10 Page - STMicroelectronics

部件名 AN2156
功能描述  STR73x Hardware Getting Started
PDF  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

AN2156 数据表(HTML) 10 Page - STMicroelectronics

Back Button AN2156 Datasheet HTML 6Page - STMicroelectronics AN2156 Datasheet HTML 7Page - STMicroelectronics AN2156 Datasheet HTML 8Page - STMicroelectronics AN2156 Datasheet HTML 9Page - STMicroelectronics AN2156 Datasheet HTML 10Page - STMicroelectronics AN2156 Datasheet HTML 11Page - STMicroelectronics AN2156 Datasheet HTML 12Page - STMicroelectronics AN2156 Datasheet HTML 13Page - STMicroelectronics AN2156 Datasheet HTML 14Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 24 page
background image
4 - Boot management
AN2156
10/24
Figure 7.
Timing diagram for RSTIN, M0 and M1
SystemMemory
Boot mode with support of external HW such as a Tester
The easiest way to support the SystemMemory boot mode without adding much complexity
and cost is to replace the direct connection of M0 and M1 pins towards GND with pull-down
resistors and to add one test pin each directly connected to M0 and M1. The pull-down
resistors should have a value of around 10kΩ. If no further hardware is connected to the
testpins the user boot mode will be selected. If however a tester provides the necessary
dynamic voltages to the testpins via a needle adaptor the SystemMemory bootmode can be
used.
Figure 8.
M1 and M0 connections giving support for external tester
SystemMemory
Boot mode with onboard circuitry
The necessary dynamic signals can also be generated by onboard circuitry so that no external
hardware is necessary. The following schematic shows how this could be done. During active
reset (nRSTIN low) the transistor is in high impedance and the capacitor is uncharged through
the two resistors R1, resulting in M1 being high. As soon as the reset signal is deasserted high
the transistor switches to low impedance after the charge of the capacitor via resistor R1 and
R3.(when the Vbe of the transistor is upper than 0.7V). As a consequence M0 will become low
after a period of a few µs.
RSTIN
M0
M1
Latching of M0 and M1
>500ns
M0
M1
R2
R1
Testpoint
Testpoint



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com