PIC16C925T-SSLASHCL datasheet(63/182 Pages) MICROCHIP

63 / 182 page

 2001 Microchip Technology Inc.

Preliminary

DS39544A-page 61

PIC16C925/926

9.1

SPI Mode

The SPI mode allows 8-bits of data to be synchro-

nously transmitted and received simultaneously. To

accomplish communication, typically three pins are

used:

• Serial Data Out (SDO) RC5/SDO

• Serial Data In (SDI) RC4/SDI

• Serial Clock (SCK) RC3/SCK

Additionally, a fourth pin may be used when in a Slave

mode of operation:

• Slave Select (SS) RA5/AN4/SS

When initializing the SPI, several options need to be

specified. This is done by programming the appropriate

control bits in the SSPCON register (SSPCON<5:0>)

and SSPSTAT<7:6>. These control bits allow the fol-

lowing to be specified:

• Master mode (SCK is the clock output)

• Slave mode (SCK is the clock input)

• Clock Polarity (Idle state of SCK)

• Clock Edge (output data on rising/falling edge of

SCK)

• Clock Rate (Master mode only)

• Slave Select mode (Slave mode only)

The SSP consists of a transmit/receive shift register

(SSPSR) and a buffer register (SSPBUF). The SSPSR

shifts the data in and out of the device, MSb first. The

SSPBUF holds the data that was written to the SSPSR,

until the received data is ready. Once the 8-bits of data

have been received, that byte is moved to the SSPBUF

Then,

the

buffer

full

detect

bit,

(SSPSTAT<0>),

and

interrupt

flag

bit,

SSPIF

(PIR1<3>), are set. This double buffering of the

received data (SSPBUF) allows the next byte to start

reception before reading the data that was just

received. Any write to the SSPBUF register during

transmission/reception of data will be ignored, and the

write collision detect bit, WCOL (SSPCON<7>), will be

set. User software must clear the WCOL bit so that it

can be determined if the following write(s) to the

SSPBUF register completed successfully. When the

application software is expecting to receive valid data,

the SSPBUF should be read before the next byte of

data to transfer is written to the SSPBUF. Buffer full bit,

BF (SSPSTAT<0>), indicates when SSPBUF has been

loaded with the received data (transmission is com-

plete). When the SSPBUF is read, bit BF is cleared.

This data may be irrelevant if the SPI is only a transmit-

ter. Generally, the SSP interrupt is used to determine

when the transmission/reception has completed. The

SSPBUF must be read and/or written. If the interrupt

method is not going to be used, then software polling

can be done to ensure that a write collision does not

occur. Example 9-1 shows the loading of the SSPBUF

(SSPSR) for data transmission. The MOVWF RXDATA

instruction (shaded) is only required if the received data

is meaningful.

EXAMPLE 9-1:

LOADING THE SSPBUF

(SSPSR) REGISTER

The block diagram of the SSP module, when in SPI

mode (Figure 9-1), shows that the SSPSR is not

directly readable or writable, and can only be accessed

from addressing the SSPBUF register. Additionally, the

SSP status register (SSPSTAT) indicates the various

status conditions.

FIGURE 9-1:

SSP BLOCK DIAGRAM

(SPI MODE)

BCF

STATUS, RP1

;Select Bank1

BSF

STATUS, RP0

;

LOOP

BTFSS SSPSTAT, BF

;Has data been

;received

;(transmit

;complete)?

GOTO

LOOP

;No

BCF

STATUS, RP0

;Select Bank0

MOVF

SSPBUF, W

;W reg = contents

;of SSPBUF

MOVF

TXDATA, W

;W reg = contents

; of TXDATA

MOVWF SSPBUF

;New data to xmit

MOVWF RXDATA

;Save in user RAM

Read

Write

Internal

Data Bus

RC4/SDI/SDA

RC5/SDO

RA5/AN4/SS

RC3/SCK/

SSPSR reg

SSPBUF reg

SSPM3:SSPM0

bit0

Shift

Clock

SS Control

Enable

Edge

Select

Clock Select

TMR2 Output

TCY

Prescaler

4, 16, 64

TRISC<3>

Edge

Select

SCL

PIC16C925T-S/CL 数据表(PDF) 63 Page - Microchip Technology

PIC16C925T-S/CL 数据表(HTML) 63 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载