STRFNFCA datasheet(37/74 Pages) STMICROELECTRONICS

37 / 74 page

STRFNFCA

Commands

Doc ID 023077 Rev 10

37/74

●

Maxsleep (Byte 16): The STRFNFCA emits (MaxSleep +1) bursts before leaving Tag

Detection mode if bit 0 (Timer Out) of the WU source register is set to ‘1’. Otherwise,

when this bit is set to ‘0’, a burst is emitted indefinitely.

Note:

Bytes 4 to 9 should be used as shown in the examples in Section 5.9: Idle command (0x07)

description.

Note that the MaxSleep value is coded on the 5 least significant bits, thus:

0x00 < MaxSleep < 0x1F.

All the previously described command parameters must be chosen accordingly for the initial

tag detection calibration when setting up the STRFNFCA.

Their value will impact tag detection efficiency, and STRFNFCA power consumption during

Tag Detection periods.

5.9.5

Tag detection calibration procedure

The Idle command allows the use of a tag detection as a wake-up event. Certain

parameters of the Idle command are dedicated to setting the conditions of a tag detection

sequence.

During the tag detection sequence, the STRFNFCA regularly emits RF bursts and

measures the current in the antenna driver IDRIVE using the internal 6-bit DAC.

When a tag enters the STRFNFCA antenna RF operating volume, it modifies the antenna

loading characteristics and induces a change in IDRIVE, and consequently, the DAC data

This value is then compared to the reference value established during the tag detection

calibration process. This enables the STRFNFCA to decide if a tag has entered or not its

operating volume.

The reference value (DacDataRef) is established during a tag detection calibration process

using the STRFNFCA application setting with no tag in its environment.

The calibration process consists in executing a tag detection sequence using a well-known

configuration, with no tag within the antenna RF operating volume, to determine a specific

reference value (DacDataRef) that will be reused by the host to define the tag detection

parameters (DacDataL and DacDataH).

During the calibration process, DacDataL is forced to 0x00 and the software successively

varies the DacDataH value from its maximum value (0xFE) to it minimum value (0x00). At

the end of the calibration process, DacDataRef will correspond to the value of DacDataH for

which the wake-up event switches from Timeout (no tag in the RF field) to tag detected.

To avoid too much sensitivity of the tag detection process, we recommend using a guard

band. This value corresponds to 2 DAC steps (0x08).

Recommended guard band value:

DacDataL = DacDataRef – Guard and DacDataH = DacDataRef + Guard

The parameters used to define the tag detection calibration sequence (clocking, set-up time,

burst duration, etc.) must be the same as those used for the future tag detection sequences.

When executing a tag detection sequence, the STRFNFCA compares the DAC data register

value to the DAC Data parameter values (DacDataL and DacDataH) included in the Idle

command. The STRFNFCA will exit WFE mode through a Tag Detection event if the DAC

data register value is greater than the DAC Data parameter high value (DacDataH) or less

than the DAC Data parameter low value (DacDataL). Otherwise, it will return to Ready state

after a Timeout.

STRFNFCA 数据表(PDF) 37 Page - STMicroelectronics

STRFNFCA 数据表(HTML) 37 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

数据表下载