PIC16F877ATISLASHML datasheet(123/234 Pages) MICROCHIP

123 / 234 page

 2003 Microchip Technology Inc.

DS39582B-page 121

PIC16F87XA

10.3

USART Synchronous

Master Mode

In Synchronous Master mode, the data is transmitted in

a half-duplex manner (i.e., transmission and reception

do not occur at the same time). When transmitting data,

the reception is inhibited and vice versa. Synchronous

mode is entered by setting bit, SYNC (TXSTA<4>). In

addition, enable bit, SPEN (RCSTA<7>), is set in order

to configure the RC6/TX/CK and RC7/RX/DT I/O pins

to CK (clock) and DT (data) lines, respectively. The

Master mode indicates that the processor transmits the

master clock on the CK line. The Master mode is

entered by setting bit, CSRC (TXSTA<7>).

10.3.1

USART SYNCHRONOUS MASTER

TRANSMISSION

The USART transmitter block diagram is shown in

Figure 10-6. The heart of the transmitter is the Transmit

(Serial) Shift Register (TSR). The shift register obtains

its data from the Read/Write Transmit Buffer register,

TXREG. The TXREG register is loaded with data in

software. The TSR register is not loaded until the last

bit has been transmitted from the previous load. As

soon as the last bit is transmitted, the TSR is loaded

with new data from the TXREG (if available). Once the

TXREG register transfers the data to the TSR register

(occurs in one TCYCLE), the TXREG is empty and inter-

rupt bit, TXIF (PIR1<4>), is set. The interrupt can be

enabled/disabled by setting/clearing enable bit TXIE

(PIE1<4>). Flag bit TXIF will be set regardless of the

state of enable bit TXIE and cannot be cleared in soft-

ware. It will reset only when new data is loaded into the

TXREG register. While flag bit TXIF indicates the status

of the TXREG register, another bit, TRMT (TXSTA<1>),

shows the status of the TSR register. TRMT is a read-

only bit which is set when the TSR is empty. No inter-

rupt logic is tied to this bit so the user has to poll this bit

in order to determine if the TSR register is empty. The

TSR is not mapped in data memory so it is not available

to the user.

Transmission is enabled by setting enable bit, TXEN

(TXSTA<5>). The actual transmission will not occur

until the TXREG register has been loaded with data.

The first data bit will be shifted out on the next available

rising edge of the clock on the CK line. Data out is

stable around the falling edge of the synchronous clock

(Figure 10-9). The transmission can also be started by

first loading the TXREG register and then setting bit

TXEN (Figure 10-10). This is advantageous when slow

baud rates are selected since the BRG is kept in Reset

when bits TXEN, CREN and SREN are clear. Setting

enable bit TXEN will start the BRG, creating a shift

clock immediately. Normally, when transmission is first

started, the TSR register is empty so a transfer to the

TXREG register will result in an immediate transfer to

TSR, resulting in an empty TXREG. Back-to-back

transfers are possible.

Clearing enable bit TXEN during a transmission will

cause the transmission to be aborted and will reset the

transmitter. The DT and CK pins will revert to high-

impedance. If either bit CREN or bit SREN is set during

a transmission, the transmission is aborted and the DT

pin reverts to a high-impedance state (for a reception).

The CK pin will remain an output if bit CSRC is set

(internal clock). The transmitter logic, however, is not

reset, although it is disconnected from the pins. In order

to reset the transmitter, the user has to clear bit TXEN.

If bit SREN is set (to interrupt an on-going transmission

and receive a single word), then after the single word is

received, bit SREN will be cleared and the serial port

will revert back to transmitting since bit TXEN is still set.

The DT line will immediately switch from High-

Impedance Receive mode to transmit and start driving.

To avoid this, bit TXEN should be cleared.

In order to select 9-bit transmission, the TX9

(TXSTA<6>) bit should be set and the ninth bit should

be written to bit TX9D (TXSTA<0>). The ninth bit must

be written before writing the 8-bit data to the TXREG

result in an immediate transfer of the data to the TSR

the TXREG was written before writing the “new” TX9D,

the “present” value of bit TX9D is loaded.

Steps to follow when setting up a Synchronous Master

Transmission:

Initialize the SPBRG register for the appropriate

baud rate (Section 10.1 “USART Baud Rate

Generator (BRG)”).

Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

If interrupts are desired, set enable bit TXIE.

If 9-bit transmission is desired, set bit TX9.

Enable the transmission by setting bit TXEN.

If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

Start transmission by loading data to the TXREG

If using interrupts, ensure that GIE and PEIE

(bits 7 and 6) of the INTCON register are set.

PIC16F877ATI/ML 数据表(PDF) 123 Page - Microchip Technology

PIC16F877ATI/ML 数据表(HTML) 123 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载