COP688CS datasheet(22/53 Pages) NSC

22 / 53 page

Timers (Continued)

The timer mode control bits (TxC3, TxC2 and TxC1) are detailed below:

Mode

TxC3

TxC2

TxC1

Description

Interrupt A

Source

Interrupt B

Source

Timer

Counts On

PWM: TxA Toggle

Autoreload RA

Autoreload RB

PWM: No TxA

Toggle

Autoreload RA

Autoreload RB

External Event

Counter

Timer

Underflow

Pos. TxB Edge

Pos. TxA

Edge

External Event

Counter

Timer

Underflow

Pos. TxB Edge

Pos. TxA

Edge

Captures:

Pos. TxA Edge

Pos. TxB Edge

TxA Pos. Edge

or Timer

TxB Pos. Edge

Underflow

Captures:

Pos. TxA

Neg. TxB

TxA Pos. Edge

Edge or Timer

Edge

TxB Neg. Edge

Underflow

Captures:

Neg. TxA

Neg. TxB

TxA Neg. Edge

Edge or Timer

Edge

TxB Neg. Edge

Underflow

Captures:

Neg. TxA

Neg. TxB

TxA Neg. Edge

Edge or Timer

Edge

TxB Neg. Edge

Underflow

Power Save Modes

The device offers the user two power save modes of opera-

tion: HALT and IDLE. In the HALT mode, all microcontroller

activities are stopped. In the IDLE mode, the on-board oscil-

lator circuitry and timer T0 are active but all other microcon-

troller activities are stopped. In either mode, all on-board

RAM, registers, I/O states, and timers (with the exception of

T0) are unaltered.

HALT MODE

The device can be placed in the HALT mode by writing a “1”

to the HALT flag (G7 data bit). All microcontroller activities,

including the clock and timers, are stopped. The WATCH-

DOG logic on the device is disabled during the HALT mode.

However, the clock monitor circuitry if enabled remains ac-

tive and will cause the WATCHDOG output pin (WDOUT) to

go low. If the HALT mode is used and the user does not want

to activate the WDOUT pin, the Clock Monitor should be dis-

abled after the device comes out of reset (resetting the Clock

Monitor control bit with the first write to the WDSVR register).

In the HALT mode, the power requirements of the device are

minimal and the applied voltage (V

CC) may be decreased to

r (Vr = 2.0V) without altering the state of the machine.

The device supports three different ways of exiting the HALT

mode. The first method of exiting the HALT mode is with the

Multi-Input Wakeup feature on the L port. The second

method is with a low to high transition on the CKO (G7) pin.

This method precludes the use of the crystal clock configura-

tion (since CKO becomes a dedicated output), and so may

only be used with an RC clock configuration. The third

method of exiting the HALT mode is by pulling the RESET

pin low.

Since a crystal or ceramic resonator may be selected as the

oscillator, the Wakeup signal is not allowed to start the chip

running immediately since crystal oscillators and ceramic

resonators have a delayed start up time to reach full ampli-

tude and frequency stability. The IDLE timer is used to gen-

erate a fixed delay to ensure that the oscillator has indeed

stabilized before allowing instruction execution. In this case,

upon detecting a valid Wakeup signal, only the oscillator cir-

cuitry is enabled. The IDLE timer is loaded with a value of

256 and is clocked with the t

c instruction cycle clock. The tc

clock is derived by dividing the oscillator clock down by a fac-

tor of 10. The Schmitt trigger following the CKI inverter on

the chip ensures that the IDLE timer is clocked only when the

oscillator has a sufficiently large amplitude to meet the

Schmitt trigger specifications. This Schmitt trigger is not part

of the oscillator closed loop. The startup timeout from the

IDLE timer enables the clock signals to be routed to the rest

of the chip.

If an RC clock option is being used, the fixed delay is intro-

duced optionally. A control bit, CLKDLY, mapped as configu-

ration bit G7, controls whether the delay is to be introduced

or not. The delay is included if CLKDLY is set, and excluded

if CLKDLY is reset. The CLKDLY bit is cleared on reset.

The device has two mask options associated with the HALT

mode. The first mask option enables the HALT mode feature,

while the second mask option disables the HALT mode. With

the HALT mode enable mask option, the device will enter

and exit the HALT mode as described above. With the HALT

disable mask option, the device cannot be placed in the

HALT mode (writing a “1” to the HALT flag will have no effect,

the HALT flag will remain “0”).

IDLE MODE

The device is placed in the IDLE mode by writing a “1” to the

IDLE flag (G6 data bit). In this mode, all activities, except the

associated on-board oscillator circuitry and the IDLE Timer

T0, are stopped. The power supply requirements of the

COP688CS 数据表(PDF) 22 Page - National Semiconductor (TI)

COP688CS 数据表(HTML) 22 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

数据表下载

链接网址

COP688CS 数据表(PDF) 22 Page - National Semiconductor (TI)

COP688CS 数据表(HTML) 22 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

数据表 下载

链接网址

数据表下载