P89LPC921 datasheet(33/45 Pages) PHILIPS

33 / 45 page

Philips Semiconductors

P89LPC920/921/922

8-bit microcontrollers with two-clock 80C51 core

Product data

Rev. 06 — 21 November 2003

33 of 45

9397 750 12285

In-System Programming (ISP): In-System Programming is performed without

removing the microcontroller from the system. The In-System Programming facility

consists of a series of internal hardware resources coupled with internal ﬁrmware to

facilitate remote programming of the P89LPC920/921/922 through the serial port.

This ﬁrmware is provided by Philips and embedded within each P89LPC920/921/922

device. The Philips In-System Programming facility has made in-system

programming in an embedded application possible with a minimum of additional

expense in components and circuit board area. The ISP function uses ﬁve pins (VDD,

VSS, TXD, RXD, and RST). Only a small connector needs to be available to interface

your application to an external circuit in order to use this feature. Please see the

P89LPC920/921/922 User’s Manual for additional details.

In-Application Programming (IAP): Several In-Application Programming (IAP) calls

are available for use by an application program to permit selective erasing and

programming of Flash sectors, pages, security bits, conﬁguration bytes, and device

identiﬁcation. All calls are made through a common interface, PGM_MTP. The

programming functions are selected by setting up the microcontroller’s registers

before making a call to PGM_MTP at FF00H. Please see the

P89LPC920/921/922

User’s Manual for additional details.

In-Circuit Programming (ICP): In-Circuit Programming is a method intended to

allow commercial programmers to program and erase these devices without

removing the microcontroller from the system. The In-Circuit Programming facility

consists of a series of internal hardware resources to facilitate remote programming

of the P89LPC920/921/922 through a two-wire serial interface. Philips has made

in-circuit programming in an embedded application possible with a minimum of

additional expense in components and circuit board area. The ICP function uses ﬁve

pins (VDD, VSS, P0.5, P0.4, and RST). Only a small connector needs to be available

to interface your application to an external programmer in order to use this feature.

8.25 User conﬁguration bytes

A number of user-conﬁgurable features of the P89LPC920/921/922 must be deﬁned

at power-up and therefore cannot be set by the program after start of execution.

These features are conﬁgured through the use of the Flash byte UCFG1. Please see

the

P89LPC920/921/922 User’s Manual for additional details.

8.26 User sector security bytes

There are two/four/eight User Sector Security Bytes, each corresponding to one

sector. Please see the

P89LPC920/921/922 User’s Manual for additional details.

P89LPC921 数据表(PDF) 33 Page - NXP Semiconductors

P89LPC921 数据表(HTML) 33 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表下载

链接网址

P89LPC921 数据表(PDF) 33 Page - NXP Semiconductors

P89LPC921 数据表(HTML) 33 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表 下载

链接网址

数据表下载