SN65MLVD080

SN65MLVD082

SLLS581A − SEPTEMBER 2003 − REVISED SEPTEMBER 2003

www.ti.com

4

RECEIVER ELECTRICAL CHARACTERISTICS

over recommended operating conditions unless otherwise noted(1)

PARAMETER

TEST CONDITIONS

MIN

TYP(1)

MAX

UNIT

VIT+

Positive-going differential input voltage

Type 1

50

mV

VIT+

Positive-going differential input voltage

threshold (A, B)

Type 2

150

mV

VIT−

Negative-going differential input voltage

Type 1

See Figure 9 and Table 1 and

−50

mV

VIT−

Negative-going differential input voltage

threshold (A, B)

Type 2

See Figure 9 and Table 1 and

Table 2

50

mV

VHYS

Differential input voltage hysteresis,

Type 1

Table 2

25

mV

VHYS

Differential input voltage hysteresis,

(VIT+ − VIT) (A, B)

Type 2

0

mV

VOH

High-level output voltage (R)

IOH = −8 mA

2.4

V

VOL

Low-level output voltage (R)

IOL = 8 mA

0.4

V

IIH

High-level input current (RE)

VIH = 2 V to VCC

−10

µA

IIL

Low-level input current (RE)

VIL = GND to 0.8 V

−10

µA

IOZ

High-impedance output current (R)

VO = 0 V or VCC

−10

15

µA

(1) All typical values are at 25°C and with a 3.3-V supply voltage.

BUS INPUT AND OUTPUT ELECTRICAL CHARACTERISTICS

over recommended operating conditions unless otherwise noted

PARAMETER

TEST CONDITIONS

MIN

TYP(1)

MAX

UNIT

Receiver or transceiver with driver

VA = 3.8 V,

VB = 1.2 V,

0

32

IA

Receiver or transceiver with driver

disabled input current

VA = 0 V or 2.4 V,

VB = 1.2 V

−20

20

µA

IA

disabled input current

VA = −1.4 V,

VB = 1.2 V

−32

0

µA

Receiver or transceiver with driver

VB = 3.8 V,

VA = 1.2 V

0

32

IB

Receiver or transceiver with driver

disabled input current

VB = 0 V or 2.4 V,

VA = 1.2 V

−20

20

µA

IB

disabled input current

VB = −1.4 V,

VA = 1.2 V

−32

0

µA

IAB

Receiver or transceiver with driver

disabled differential input current

(IA − IB)

VA = VB,

−1.4

≤ VA ≤ 3.8 V

−4

4

µA

Receiver or transceiver power-off input

VA = 3.8 V,

VB = 1.2 V, 0 V ≤ VCC ≤ 1.5 V

0

32

IA(OFF)

Receiver or transceiver power-off input

current

VA = 0 V or 2.4 V,

VB = 1.2 V, 0 V ≤ VCC ≤ 1.5 V

−20

20

µA

IA(OFF)

current

VA = −1.4 V,

VB= 1.2 V,

0 V

≤ VCC ≤ 1.5 V

−32

0

µA

Receiver or transceiver power-off input

VB = 3.8 V,

VA = 1.2 V, 0 V ≤ VCC ≤ 1.5 V

0

32

IB(OFF)

Receiver or transceiver power-off input

current

VB = 0 V or 2.4 V,

VA = 1.2 V, 0 V ≤ VCC ≤ 1.5 V

−20

20

µA

IB(OFF)

current

VB = −1.4 V,

VA = 1.2 V, 0 V ≤ VCC ≤ 1.5 V

−32

0

µA

IAB(OFF)

Receiver input or transceiver

power-off differential input current

(IA(off) − IB(off))

VA = VB, 0 V ≤ VCC ≤ 1.5 V, −1.4 ≤ VA ≤ 3.8 V

−4

4

µA

CA

Transceiver with driver disabled input

capacitance

VA = 0.4 sin (30E6πt) + 0.5V(2), VB =1.2 V

5

pF

CB

Transceiver with driver disabled input

capacitance

VB = 0.4 sin (30E6πt) + 0.5V(2), VA =1.2 V

5

pF

CAB

Transceiver with driver disabled

differential input capacitance

VAB = 0.4 sin (30E6πt)V (2)

3

pF

CA/B

Transceiver with driver disabled input

capacitance balance, (CA/CB)

0.99

1.01

(1) All typical values are at 25°C and with a 3.3-V supply voltage.

(2) HP4194A impedance analyzer (or equivalent)