SST25VF080B datasheet(4/32 Pages) MICROCHIP

4 / 32 page

SST25VF080B

DS20005045C-page 4

 2015 Microchip Technology Inc.

3.0

MEMORY ORGANIZATION

The SST25VF080B SuperFlash memory array is orga-

nized in uniform 4 KByte erasable sectors with 32

KByte overlay blocks and 64 KByte overlay erasable

blocks.

4.0

DEVICE OPERATION

The SST25VF080B is accessed through the SPI (Serial

Peripheral Interface) bus compatible protocol. The SPI

bus consist of four control lines; Chip Enable (CE#) is

used to select the device, and data is accessed through

the Serial Data Input (SI), Serial Data Output (SO), and

Serial Clock (SCK).

The SST25VF080B supports both Mode 0 (0,0) and

Mode 3 (1,1) of SPI bus operations. The difference

between the two modes, as shown in Figure 4-1, is the

state of the SCK signal when the bus master is in

Stand-by mode and no data is being transferred. The

SCK signal is low for Mode 0 and SCK signal is high for

Mode 3. For both modes, the Serial Data In (SI) is sam-

pled at the rising edge of the SCK clock signal and the

Serial Data Output (SO) is driven after the falling edge

of the SCK clock signal.

FIGURE 4-1:

SPI PROTOCOL

4.1

Hold Operation

The HOLD# pin is used to pause a serial sequence

underway with the SPI flash memory without resetting

the clocking sequence. To activate the HOLD# mode,

CE# must be in active low state. The HOLD# mode

begins when the SCK active low state coincides with

the falling edge of the HOLD# signal. The HOLD mode

ends when the HOLD# signal’s rising edge coincides

with the SCK active low state.

If the falling edge of the HOLD# signal does not coin-

cide with the SCK active low state, then the device

enters Hold mode when the SCK next reaches the

active low state. Similarly, if the rising edge of the

HOLD# signal does not coincide with the SCK active

low state, then the device exits in Hold mode when the

SCK next reaches the active low state. See Figure 4-2

for Hold Condition waveform.

Once the device enters Hold mode, SO will be in high-

impedance state while SI and SCK can be VIL or VIH.

If CE# is driven active high during a Hold condition, it

resets the internal logic of the device. As long as

HOLD# signal is low, the memory remains in the Hold

condition. To resume communication with the device,

HOLD# must be driven active high, and CE# must be

driven active low. See Figure 5-3 for Hold timing.

FIGURE 4-2:

HOLD CONDITION WAVEFORM

1296 SPIprot.0

MODE 3

SCK

CE#

MODE 3

DON'T CARE

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

MODE 0

HIGH IMPEDANCE

MSB

Active

Hold

Active

Hold

Active

1296 HoldCond.0

SCK

HOLD#

SST25VF080B 数据表(PDF) 4 Page - Microchip Technology

SST25VF080B 数据表(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表下载

链接网址

SST25VF080B 数据表(PDF) 4 Page - Microchip Technology

SST25VF080B 数据表(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表 下载

链接网址

数据表下载