DA14581_16 datasheet(41/153 Pages) DIALOG

41 / 153 page

Datasheet

Revision 3.2

17-Jan-2017

CFR0011-120-01

41 of 153

DA14581

Bluetooth Low Energy 4.2 SoC with Optimized Boot Time

FINAL

UART_RFE

Receiver FIFO Error bit.

This bit is only relevant when FIFOs are enabled (FCR[0] set

to one). This is used to indicate if there is at least one parity

error, framing error, or break indication in the FIFO.

0 = no error in RX FIFO

1 = error in RX FIFO

This bit is cleared when the LSR is read and the character

with the error is at the top of the receiver FIFO and there are

no subsequent errors in the FIFO.

0x0

UART_TEMT

Transmitter Empty bit.

If FIFOs enabled (FCR[0] set to one), this bit is set whenever

the Transmitter Shift Register and the FIFO are both empty.

If FIFOs are disabled, this bit is set whenever the Transmitter

Holding Register and the Transmitter Shift Register are both

empty.

0x1

UART_THRE

Transmit Holding Register Empty bit.

If THRE mode is disabled (IER[7] set to zero) and regardless

of FIFO's being implemented/enabled or not, this bit indi-

cates that the THR or TX FIFO is empty.

This bit is set whenever data is transferred from the THR or

TX FIFO to the transmitter shift register and no new data has

been written to the THR or TX FIFO. This also causes a

THRE Interrupt to occur, if the THRE Interrupt is enabled. If

both modes are active (IER[7] set to one and FCR[0] set to

one respectively), the functionality is switched to indicate the

transmitter FIFO is full, and no longer controls THRE inter-

rupts, which are then controlled by the FCR[5:4] threshold

setting.

0x1

UART_B1

Break Interrupt bit.

This is used to indicate the detection of a break sequence on

the serial input data.

If in UART mode (SIR_MODE == Disabled), it is set when-

ever the serial input, sin, is held in a logic '0' state for longer

than the sum of start time + data bits + parity + stop bits.

If in infrared mode (SIR_MODE == Enabled), it is set when-

ever the serial input, sir_in, is continuously pulsed to logic '0'

for longer than the sum of start time + data bits + parity +

stop bits. A break condition on serial input causes one and

only one character, consisting of all zeros, to be received by

the UART.

In the FIFO mode, the character associated with the break

condition is carried through the FIFO and is revealed when

the character is at the top of the FIFO.

Reading the LSR clears the BI bit. In the non-FIFO mode,

the BI indication occurs immediately and persists until the

LSR is read.

0x0

Table 51: UART_LSR_REG (0x50001014)

Bit

Mode

Symbol

Description

Reset

DA14581 数据表(PDF) 41 Page - Dialog Semiconductor

DA14581 数据表(HTML) 41 Page - Dialog Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载