CS5532-AS datasheet(15/52 Pages) CIRRUS

15 / 52 page

CS5531/32/33/34

DS289PP5

-40°C to +85°C (MCLK=4.9152 MHz). The com-

mon-mode plus signal range of the instrumentation

amplifier is (VA-) + 0.7 V to (VA+) - 1.7 V.

Figure 4 illustrates the input models for the ampli-

fiers. The dynamic input current for each of the

pins can be determined from the models shown.

Note:

The C=2.5pF and C = 16pF capacitors are for

input current modeling only. For physical

input capacitance see ‘Input Capacitance’

specification under Analog Characteristics.

2.1.1. Analog Input Span

The full scale input signal that the converter can dig-

itize is a function of the gain setting and the refer-

ence voltage connected between the VREF+ and

VREF- pins. The full scale input span of the convert-

er is ((VREF+) - (VREF-))/(GxA), where G is the

gain of the amplifier and A is 2 for VRS = 0, or A is

1 for VRS = 1. VRS is the Voltage Reference Select

bit, and must be set according to the differential volt-

age applied to the VREF+ and VREF- pins on the

part. See section 2.3.5 for more details.

After reset, the unity gain buffer is engaged. With a

2.5V reference this would make the full scale input

range default to 2.5 V. By activating the instrumen-

tation amplifier (i.e. a gain setting other than 1) and

using a gain setting of 32, the full scale input range

can quickly be set to 2.5/32 or about 78 mV. Note

that these input ranges assume the calibration regis-

ters are set to their default values (i.e. Gain = 1.0 and

Offset = 0.0).

2.1.2. Multiplexed Settling Limitations

The settling performance of the CS5531/32/33/34

in multiplexed applications is affected by the sin-

gle-pole low-pass filter which follows the instru-

mentation amplifier (see Figure 3). To achieve data

sheet settling and linearity specifications, it is rec-

ommended that a 22 nF C0G capacitor be used. Ca-

pacitors as low as 10 nF or X7R type capacitors can

also be used with some minor increase in distortion

for AC signals.

2.1.3. Voltage Noise Density Performance

Figure 5 illustrates the measured voltage noise den-

sity versus frequency from 0.01 Hz to 10 Hz of a

CS5532-BS. The device was powered with ±2.5 V

supplies, using 120 Sps OWR, the 64x gain range,

bipolar mode, and with the input short bit enabled.

2.1.4. No Offset DAC

An offset DAC was not included in the CS553X

family because the high dynamic range of the con-

verter eliminates the need for one. The offset regis-

AIN

Gain = 2,4,8,16, 32, 64

C =12.5 pF

Gain = 1

AIN

C= 80 pF

φ Coarse

φ Fine

≤ 20 mV

i= fV

≤ 1mV

i= fV

MCLK

128

MCLK

Figure 4. Input models for AIN+ and AIN- pins

100

0.01

0.1

Frequency (Hz)

Gain = 64

Figure 5. Measured Voltage Noise Density

CS5532-AS 数据表(PDF) 15 Page - Cirrus Logic

CS5532-AS 数据表(HTML) 15 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载