PIC18LF4520ESLASHSPQTP datasheet(151/390 Pages) MICROCHIP

151 / 390 page

 2004 Microchip Technology Inc.

Preliminary

DS39631A-page 149

PIC18F2420/2520/4420/4520

16.4

Enhanced PWM Mode

The Enhanced PWM mode provides additional PWM

output options for a broader range of control applica-

tions. The module is a backward compatible version of

the standard CCP module and offers up to four outputs,

designated P1A through P1D. Users are also able to

select the polarity of the signal (either active-high or

active-low). The module’s output mode and polarity are

configured

setting

the

P1M1:P1M0

and

CCP1M3:CCP1M0 bits of the CCP1CON register.

Figure 16-1 shows a simplified block diagram of PWM

operation. All control registers are double-buffered and

are loaded at the beginning of a new PWM cycle (the

period boundary when Timer2 resets) in order to pre-

vent glitches on any of the outputs. The exception is the

PWM Delay register, PWM1CON, which is loaded at

either the duty cycle boundary or the period boundary

(whichever comes first). Because of the buffering, the

module waits until the assigned timer resets, instead of

starting immediately. This means that enhanced PWM

waveforms do not exactly match the standard PWM

waveforms, but are instead offset by one full instruction

cycle (4 TOSC).

As before, the user must manually configure the

appropriate TRIS bits for output.

16.4.1

PWM PERIOD

The PWM period is specified by writing to the PR2

following equation.

EQUATION 16-1:

PWM frequency is defined as 1/[PWM period]. When

TMR2 is equal to PR2, the following three events occur

on the next increment cycle:

•TMR2 is cleared

• The CCP1 pin is set (if PWM duty cycle = 0%, the

CCP1 pin will not be set)

• The PWM duty cycle is copied from CCPR1L into

CCPR1H

FIGURE 16-1:

SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE

Note:

The Timer2 postscaler (see Section 13.0

“Timer2 Module”) is not used in the

determination of the PWM frequency. The

postscaler could be used to have a servo

update rate at a different frequency than

the PWM output.

PWM Period =

[(PR2) + 1] • 4 • TOSC •

(TMR2 Prescale Value)

CCPR1L

CCPR1H (Slave)

Comparator

TMR2

Comparator

PR2

(Note 1)

Duty Cycle Registers

CCP1CON<5:4>

Clear Timer,

set CCP1 pin and

latch D.C.

Note: The 8-bit TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit

time base.

TRISx<x>

CCP1/P1A

TRISx<x>

P1B

TRISx<x>

P1D

Output

Controller

P1M1<1:0>

CCP1M<3:0>

PWM1CON

CCP1/P1A

P1B

P1C

P1D

P1C

PIC18LF4520E/SPQTP 数据表(PDF) 151 Page - Microchip Technology

PIC18LF4520E/SPQTP 数据表(HTML) 151 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC18LF4520E/SPQTP 数据表(PDF) 151 Page - Microchip Technology

PIC18LF4520E/SPQTP 数据表(HTML) 151 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载