AVLN3L-R datasheet(50/51 Pages) ETC1

50 / 51 page

ø30 Series Instructions ø30

Safety Precautions

•Turn off the power to the ø30 series switches & pilot lights

before starting installation, removal, wiring, maintenance,

and inspection of the products. Failure to turn power off

may cause electrical shocks or fire hazard.

•To avoid a burn on your hand, use the lamp holder tool

when replacing lamps.

•For wiring, use wires of a proper size to meet the volt-

age and current requirements. Tighten the M3.5 terminal

screws to a tightening torque of 1.0 to 1.3 N·m. Failure to

tighten terminal screws may cause overheat and fire.

Instructions

Panel Mounting for Square Pushbuttons

and Pilot Lights

1. Tighten the square ring to the operator and position the

ring correctly.

2. Lightly tighten the screw to secure the pilot light onto the

panel.

Tightening Torque for Terminal Screws

Tighten the terminal screws to a torque of 1.0 to 1.3 N·m.

Replacement of Lamps

Lamps can be replaced by using the lamp holder tool (OR-

55) from the front of the panel.

How to Remove

To remove, slip the lamp holder tool onto the lamp head

lightly. Then push slightly, and turn the lamp holder tool

counterclockwise.

How to Install

To install, insert the lamp head into the lamp holder tool.

Place the pins on the lamp base to the grooves in the

lamp socket. Inset the lamp and turn it clockwise.

Installing the Anti-rotation Ring

Panel Thickness and Rubber Washer

Adjust the thickness of the rubber washers according

to the panel thickness. Also, make sure to include the

nameplate thickness when using a nameplate.

Recommended tightening

torque: 0.15 N·m

OR-55

Rubber Washer

Panel

OGL11

Anti-rotation rings are used

on selector switches or

pushbuttons which rotate

and used when using no

nameplates.

Insert a 1.5mm thick rubber

washer between the panel

and the anti-rotation ring as

shown on the right.

Applicable Models

•ExtendedIlluminatedPushbuttons

withHalfShroud(LED)

•ExtendedPushbuttonswithHalf

Shroud(Diecast)

•ExtendedIlluminatedPushbuttons

withHalfShroud(Diecast)

Panel

Thickness (mm)

Rubber Washer

1.5mm 3.0mm

Supplied

1 piece 1 piece

0.8 to 1.8

–

1 piece

1.8 to 3.5

1 piece

–

Applicable Models

•ExtendedIlluminatedPushbuttons

withFullShroud(Incandescent)

•ExtendedIlluminatedPushbuttons

withFullShroud(LED)

•ExtendedIlluminatedPushbuttons

withFullShroud(Diecast)

•MushroomPushbuttonswithFull

Shroud

Panel Thickness

(mm)

Rubber Washer

1.5mm

3.0mm

Supplied

2 pieces 1 piece

0.8 to 2.0

1 piece 1 piece

2.0 to 3.5

1 piece 1 piece

3.5 to 5.0

–

1 piece

5.0 to 6.0 (6.5)

1 piece

–

The number in brackets is for mush-

room pushbuttons with full shroud.

Extended illuminated pushbuttons

with full shroud (incandescent) are

5.0 mm maximum.

Applicable Models

•ToggleLever

•KnobPushTurnLockIlluminated

Pushbuttons

Panel Thickness

(mm)

Rubber Washer

1.5mm 3.0mm

Supplied

1 piece 1 piece

0.8 to 2.0

1 piece 1 piece

2.0 to 3.5

–

1 piece

3.5 to 5.5 (5.0)

1 piece

–

The number in brackets is for knob

push turn lock illuminated pushbut-

tons.

Applicable Models

•ExtendedPushbuttonswithHalf

Shroud

•ExtendedIlluminatedPushbuttons

withHalfShroud(Incandescent)

Panel

Thickness

(mm)

Rubber Washer

1.5mm

3.0mm

Supplied

1 piece

0.8

1 piece

0.8 to 2.3

–

1 piece

2.3 to 4.0

1 piece

–

Applicable Models

•ExtendedPushbuttonswithFull

Shroud

Panel

Thickness

(mm)

Rubber Washer

1.5mm

3.0mm

Supplied

3 pieces

1 piece

0.8 to 1.5

3 pieces

1 piece

1.5 to 3.0

2 pieces

1 piece

3.0 to 4.5

1 piece

4.5 to 6.0

–

1 piece

6.0 to 7.5

1 piece

–

Applicable Models

•ExtendedPushbuttonswithFull

Shroud(Diecast)

Panel

Thickness

(mm)

Rubber Washer

1.5mm

3.0mm

Supplied

2 pieces 1 piece

0.8 to 2.5

2 pieces 1 piece

2.5 to 4.0

1 pieces 1 piece

4.0 to 5.5

–

1 piece

5.5 to 6.0

1 piece

–

Applicable Models

•OtherModels(ExcludingSquare)

Panel

Thickness

(mm)

Rubber Washer

1.5mm

3.0mm

Supplied

2 pieces

1 piece

0.8 to 3.5

2 pieces

1 piece

3.5 to 5.0

1 piece

5.0 to 6.5

–

1 piece

6.5 to 7.5

1 piece

–

ø30

(14/03/18)

AVLN3L-R 数据表(PDF) 50 Page - List of Unclassifed Manufacturers

AVLN3L-R 数据表(HTML) 50 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表下载

链接网址

AVLN3L-R 数据表(PDF) 50 Page - List of Unclassifed Manufacturers

AVLN3L-R 数据表(HTML) 50 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表 下载

链接网址

数据表下载