P80C32 datasheet(18/62 Pages) PHILIPS

18 / 62 page

Philips Semiconductors

Product data

P80C3xX2; P80C5xX2;

P87C5xX2

80C51 8-bit microcontroller family

4K/8K/16K/32K ROM/OTP, low voltage (2.7 to 5.5 V),

low power, high speed (30/33 MHz)

2003 Jan 24

Table 4. Timer 2 Operating Modes

RCLK + TCLK

CP/RL2

TR2

MODE

16-bit Auto-reload

16-bit Capture

Baud rate generator

(off)

Symbol

Position

Name and Significance

TF2

T2CON.7

Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set

when either RCLK or TCLK = 1.

EXF2

T2CON.6

Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and

EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2

interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down

counter mode (DCEN = 1).

RCLK

T2CON.5

Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock

in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

TCLK

T2CON.4

Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock

in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

EXEN2

T2CON.3

Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative

transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to

ignore events at T2EX.

TR2

T2CON.2

Start/stop control for Timer 2. A logic 1 starts the timer.

C/T2

T2CON.1

Timer or counter select. (Timer 2)

0 = Internal timer (OSC/12 in 12-clock mode or OSC/6 in 6-clock mode)

1 = External event counter (falling edge triggered).

CP/RL2

T2CON.0

Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When

cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when

EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload

on Timer 2 overflow.

TF2

EXF2

RCLK

TCLK

EXEN2

TR2

C/T2

CP/RL2

SU01621

Bit Addressable

T2CON

Address = C8H

Reset Value = 00H

Figure 6. Timer/Counter 2 (T2CON) Control Register

P80C32 数据表(PDF) 18 Page - NXP Semiconductors

P80C32 数据表(HTML) 18 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表下载

链接网址

P80C32 数据表(PDF) 18 Page - NXP Semiconductors

P80C32 数据表(HTML) 18 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表 下载

链接网址

数据表下载