AD8155ACPZ-R7 datasheet(19/35 Pages) AD

19 / 35 page

Data Sheet

AD8155

Rev. A | Page 19 of 35

Lane Disables

By default, the receivers and transmitters enable in an on-demand

fashion according to the state of the SEL[1:0], LB_[A:C], and

BICAST pins or to the state of the equivalent registers in serial

control mode. Register 0x40, Register 0x80, and Register 0xC0

implement per-lane disables for the receivers, and Register 0x48,

ter disables. These disables override the default settings. Each

bit in the register is named for the lane and function it disables.

For example, RXDIS B0 disables the receiver on Lane 0 of Port B

whereas TXDIS C1 disables the Lane 1 transmitter of Port C

(see Table 11).

Lane Inversion: P/N Swap

The receiver P/N swap function is a convenience intended to

allow the user to implement the equivalent of a board-level

routing crossover in a much smaller area while eliminating vias

(impedance discontinuities) that compromise the high frequency

integrity of the signal path. Using this feature to correct an

inversion downstream of the receiver may require the user to

be aware of the sign of the data when switching connectivity

(the mux/demux path). The feature is available on a per-lane

setting through Register 0x44, Register 0x84, and Register

0xC4. Setting the bit true flips the sign sense of the P and N

inputs for the associated lane. The default setting is 0 (no

inversion).

Table 11. Per-Lane Disables

Address

Port

Default

Bit

Bit Name

Functionality Description

0x40

Port A

0x00

RX[A/B/C] disable

7:4

Reserved

Set to 0

0x80

Port B

0x00

3:2

Reserved

0xC0

Port C

0x00

RXDIS [A/B/C]1

0: RX Port [A/B/C], Lane 1, enabled

1: RX Port [A/B/C], Lane 1, disabled

RXDIS [A/B/C]0

0: RX Port [A/B/C], Lane 0, enabled

1: RX Port [A/B/C], Lane 0, disabled

0x48

Port A

0x00

TX[A/B/C] disable

7:4

Reserved

Set to 0

0x88

Port B

0x00

3:2

Reserved

0xC8

Port C

0x00

TXDIS [A/B/C]1

0: TX Port [A/B/C], Lane 1, enabled

1: TX Port [A/B/C], Lane 1, disabled

TXDIS [A/B/C]0

0: TX Port [A/B/C], Lane 0, enabled

1: TX Port [A/B/C], Lane 0, disabled

Table 12. Lane Inversion

Address

Port

Default

Bit

Bit Name

Functionality Description

0x44

Port A

0x00

RX[A/B/C] P/N swap

7:2

Reserved

Set to 0

0x84

Port B

0x00

PN[A/B/C]1

0: Lane 1, noninverted

1: Lane 1, inverted

0xC4

Port C

0x00

PN[A/B/C]0

0: Lane 0, noninverted

1: Lane 0, inverted

Table 13. Port-Level EQ Setting

Address

Port

Default

Bit

Bit Name

Functionality Description

0x41

Port A

0x00

RX[A/B/C] EQ setting

7:4

Reserved

Set to 0

0x81

Port B

0x00

3:0

[A/B/C]EQ[3:0]

0xC1

Port C

0x00

AD8155ACPZ-R7 数据表(PDF) 19 Page - Analog Devices

AD8155ACPZ-R7 数据表(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

数据表下载

链接网址

AD8155ACPZ-R7 数据表(PDF) 19 Page - Analog Devices

AD8155ACPZ-R7 数据表(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

数据表 下载

链接网址

数据表下载