ST10F272M datasheet(38/175 Pages) STMICROELECTRONICS

38 / 175 page

Internal Flash memory

ST10F272M

38/176

To enable Access Protection, the following sequence of operations is recommended:

●

execution from external memory or internal Rams

●

program TAUB bit at 1 in XFVTAUR0 register

●

program ACCP bit in FNVAPR0 to 0 using Set Protection operation

●

program TAUB bit at 0 in XFVTAUR0 register

●

Access Protection is active when both ACCP bit and TAUB bit are set to 0.

Protection can be permanently disabled by programming bit PDS0 of FNVAPR1H, in order

to analyze rejects. Protection can be permanently enabled again by programming bit PEN0

of FNVAPR1L. The action to disable and enable again Access Protections in a permanent

way can be executed a maximum of 16 times. To execute the above described operations,

the Flash has to be temporarily unprotected (see Section 5.5.9: Temporary unprotection).

Trying to write into the access protected Flash from internal RAM or external memories will

be unsuccessful. Trying to read into the access protected Flash from internal RAM or

external memories will output dummy data (software trap 0x009Bh).

When the Flash module is protected in access, data access through PEC of a peripheral is

also forbidden. To read/write data in PEC mode from/to a protected Bank, it is necessary to

first temporarily unprotect the Flash module.

The following table summarizes all possible Access Protection levels: In particular, it shows

what is possible and not possible to do when fetching from a memory (see fetch location

column) supposing all possible access protections are enabled.

When the Access Protection is enabled, Flash registers can not be written, so no

program/erase operation can be run on IFlash. To enable the access to registers again, the

Temporary Access Unprotection procedure has to be followed (see Section 5.5.9).

5.5.8

Write protection

The Flash modules have one level of Write Protections: each Sector of each Bank of each

Flash Module can be Software Write Protected by programming at 0 the related bit W0Px in

FNVWPIRL register.

5.5.9

Temporary unprotection

Bits W0Px of FNVWPIRL can be temporarily unprotected by executing the Set Protection

operation and by writing 1 into these bits.

Table 24.

Summary of access protection level

Fetch location

Read IFlash /

Jump to IFlash

Read XRAM or

External Memory /

Jump to XRAM or

External Memory

Read Flash

registers

Write Flash

registers

Fetching from IFlash

Yes / Yes

Yes

Fetching from IRAM

No / Yes

Yes / Yes

Fetching from XRAM

No / Yes

Yes / Yes

Fetching from External

Memory

No / Yes

Yes / Yes

ST10F272M 数据表(PDF) 38 Page - STMicroelectronics

ST10F272M 数据表(HTML) 38 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST10F272M 数据表(PDF) 38 Page - STMicroelectronics

ST10F272M 数据表(HTML) 38 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载