BMP581 datasheet(22/75 Pages) BOSCH

22 / 75 page

Bosch Sensortec | BST-BMP581-DS004-11

22 | 75

Document number: BST-BMP581-DS004-11

as well as in the event of applications for industrial property rights



shdw_sel_iir_t: select source for temperature data register



fifo_sel_iir_t: select source for temperature FIFO



shdw_sel_iir_p: select source for pressure data register



fifo_sel_iir_p: select source for pressure FIFO



oor_sel_iir_p: select source for pressure out-of-range interrupt

4.5 Data registers

Data from the most recent measurement is present in data registers. The DSP_CONFIG.swdw_sel_iir_t and

DSP_CONFIG.swdw_sel_iir_t select if IIR-filtered data or unfiltered data is presented in the data registers.

Temperature data is contained in the registers TEMP_DATA_MSB, TEMP_DATA_LSB, TEMP_DATA_XLSB. The

registers shall be interpreted in the following way:

T [°C] = (

TEMP_DATA_MSB,TEMP_DATA_LSB,TEMP_DATA_XLSB

216

)

Pressure data is contained in the registers PRESS_DATA_MSB, PRESS_DATA_LSB, PRESS_DATA_XLSB. The

registers shall be interpreted in the following way:

p [Pa] = (

PRESS_DATA_MSB,PRESS_DATA_LSB,PRESS_DATA_XLSB

)

In both equations, the divisions can be implemented by a simple and efficient bit-wise right shift operation. To read out

data after a conversion, it is strongly recommended to use a burst read and not address every register individually.

4.5.1 Data Shadowing

In normal mode, measurement timing is not necessarily synchronized to readout. This means that new measurement

results may become available while the user is reading the results from the previous measurement. In this case,

shadowing is performed in order to guarantee data consistency. Shadowing will only work if all data registers are read

in a single burst read. Therefore, the user must use burst reads if he does not synchronize data readout with the

measurement cycle. Using several independent read commands may result in inconsistent data.

If a new measurement is finished and the data registers are still being read, the new measurement results are

transferred into shadow data registers. The content of shadow registers is transferred into data registers as soon as

the user ends the burst read, even if not all data registers were read. Reading across several data registers can

therefore only be guaranteed to be consistent within one measurement cycle if a single burst read command is used.

After the end of the burst read, all user data registers are updated at once with the shadowed data.

4.6FIFO

The BMP581 contains a first-in first-out (FIFO) data buffer. Pressure and temperature data is stored in the FIFO in

frames. Each frame contains the data from one measurement. The maximum number of frames depends on which

data is stored in the FIFO:



16 frames if both pressure and temperature are stored



32 frames if only pressure or temperature is stored

4.6.1 FIFO Configuration

The FIFO frame type is selected by FIFO_SEL.fifo_frame_sel:



0b00: FIFO not enabled



0b01: Only Temperature data is stored (T-mode)

BMP581 数据表(PDF) 22 Page - Bosch Sensortec GmbH

BMP581 数据表(HTML) 22 Page - Bosch Sensortec GmbH

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

数据表下载