BMP581 datasheet(42/75 Pages) BOSCH

42 / 75 page

Bosch Sensortec | BST-BMP581-DS004-11

42 | 75

Document number: BST-BMP581-DS004-11

as well as in the event of applications for industrial property rights

5.7I3C Protocol

BMP581 supports the I³C protocol 1.0. Following I³C features are supported:

I²C compatibility including:

Support of I2C-like SDR messages to the BMP581

bus traffic of I2C messages to legacy I2C slaves

I3C single data rate (SDR) mode with up to 12.5 MHz data rate

In-Band Interrupt (IBI)

Timing control asynchronous 0 mode (restricted to maximum 11 MHz I3C frequency and a minimum of 200 kHz)

Timing control synchronous mode

The I3C bus uses the pin SCL for serial clock and SDX as SDA for serial data input and output for the signal lines.

5.7.1 I3C Identifiers

The I3C protocol uses several identifiers and codes to handle communication between several masters and slaves. For

communication with this device, there are defined the I3C provisional ID, the Device Characteristics Register (DCR), the

Bus Characteristics Register (BCR) and the Mandatory Byte (MDB) for IBIs. The I3C provisional ID has the value defined

in Table 20.

Table 23: I3C provisional identifier

The value of the Device Characteristics Register (DCR) is fixed to 0x62 to indicate a pressure sensor, as shown in Table

21. See also https://www.mipi.org/MIPI_I3C_device_characteristics_register.

Table 24: I3C device characteristics register (DCR)

DCR<7>

DCR<6>

DCR<5>

DCR<4>

DCR<3>

DCR<2>

DCR<1>

DCR<0>

Device ID

The value of the Bus Characteristics Register (BCR) is fixed to 0x06, as shown in Table 22.

Table 25: I3C bus characteristics registers (BCR)

BCR <7:6>

BCR <5>

BCR <4>

BCR <3>

BCR <2>

BCR <1>

BCR <0>

I3C Slave

Reserved

Not a bridge

Device will

always respond

to I3C Bus

commands

Mandatory

payload after IBI

IBI capable

Max data Speed:

no limitation

2’b00

1’b0

1’b1

1’b0

5.7.2 I3C In-band Interrupts

The device supports the in-band interrupt (IBI) feature of I3C, as described in the I3C specification. In case there is an

IBI event, the device will emit its address into the arbitrated address header following a START (but not following a

repeated START).

If no START is forthcoming within the Bus Available Condition, then the chip will actively pull down the SDA line to issue

a START. The IBI feature can be enabled by the Common Command Code (CCC)’ ENEC with the ENINT bit set to

0b1.The IBI feature can be disabled by the Common Command Code (CCC)’ DISEC with the DISINT bit set to 0b1.

BMP581 数据表(PDF) 42 Page - Bosch Sensortec GmbH

BMP581 数据表(HTML) 42 Page - Bosch Sensortec GmbH

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

数据表下载