AD9520-3SLASHPCBZ datasheet(45/84 Pages) AD

45 / 84 page

AD9520-3

Rev. 0 | Page 45 of 84

Either the internal VCO or the CLK can be selected as the

source for the direct-to-output signal routing. To connect the

LVPECL outputs directly to the internal VCO or CLK, the user

must select the VCO divider as the source to the distribution

section, even if no channel uses it.

Table 32. Routing VCO Divider Input Directly to the Outputs

Selection

0x1E1[1:0] = 00b

CLK is the source; VCO divider selected

0x1E1[1:0] = 10b

VCO is the source; VCO divider selected

0x192[1] = 1b

Direct-to-output OUT0, OUT1, OUT2

0x195[1] = 1b

Direct-to-output OUT3, OUT4, OUT5

0x198[1] = 1b

Direct-to-output OUT6, OUT7, OUT8

0x19B[1] = 1b

Direct-to-output OUT9, OUT10, OUT11

Clock Frequency Division

The total frequency division is a combination of the VCO

divider (when used) and the channel divider. When the VCO

divider is used, the total division from the VCO or CLK to the

output is the product of the VCO divider (1, 2, 3, 4, 5, and 6)

and the division of the channel divider. Table 33 indicates how the

frequency division for a channel is set.

Table 33. Frequency Division

CLK or VCO

Selected

VCO

Divider

Setting1

Channel

Divider

Setting

Direct-to-

Output

Setting

Resulting

Frequency

Division

CLK or VCO

input

1 to 6

Don’t

care

Enable

CLK or VCO

input

1 to 6

2 to 32

Disable

(1 to 6) ×

(2 to 32)

CLK or VCO

input

2 to 6

Bypass

Disable

(2 to 6) × (1)

CLK or VCO

input

Bypass

Disable

Output static

(illegal state)

CLK

(internal

VCO off)

VCO

divider

bypassed

Bypass

Don’t

care

CLK

(internal

VCO off)

VCO

divider

bypassed

2 to 32

Don’t

care

2 to 32

1 The bypass VCO divider (0x1E1[0] = 1) is not the same as VCO divider = 1.

The channel dividers feeding the output drivers contain one 2-

to-32 frequency divider. This divider provides for division-by-1

to division-by-32. Division-by-1 is accomplished by bypassing

the divider. The dividers also provide for a programmable duty

cycle, with optional duty-cycle correction when the divide ratio

is odd. A phase offset or delay in increments of the input clock

cycle is selectable. The channel dividers operate with a signal at

their inputs up to 1600 MHz. The features and settings of the

dividers are selected by programming the appropriate setup

and control registers (see Table 49 through Table 60).

VCO Divider

The VCO divider provides frequency division between the

internal VCO or the external CLK input and the clock

distribution channel dividers. The VCO divider can be set

to divide by 1, 2, 3, 4, 5, or 6 (see Table 56, 0x1E0[2:0]).

However, when the VCO divider is set to 1, none of the channel

output dividers can be bypassed.

The VCO divider can also be set to static, which is useful for

applications where the only desired output frequency is the

VCO frequency. Making the VCO divider static increases the

wide band spurious-free dynamic range (SFDR). If the VCO

divider is static during VCO calibration, there is no output

signal. Therefore, it is recommended that the user calibrate the

VCO with the VCO divider set to a nonstatic value during VCO

calibration, and then set the VCO divider to static after VCO

calibration is complete.

The recommended alternative to achieving the same SFDR

performance is to set the VCO divider to 1 and enable VCO

direct mode. This allows the user to program the EEPROM

with the desired values and does not require further action after

the VCO calibration is complete.

Channel Dividers

A channel divider drives each group of three LVPECL outputs.

There are four channel dividers (0, 1, 2, and 3) driving twelve

LVPECL outputs (OUT0 to OUT11). Table 34 gives the register

locations used for setting the division and other functions of

these dividers. The division is set by the values of M and N. The

divider can be bypassed (equivalent to divide-by-1, divider circuit

is powered down) by setting the bypass bit. The duty-cycle

correction can be enabled or disabled according to the setting of

the disable div DCC bits.

Table 34. Setting DX for the Output Dividers

Divider

Low Cycles

High Cycles

Bypass

Disable

Div DCC

0x190[7:4]

0x190[3:0]

0x191[7]

0x192[0]

0x193[7:4]

0x193[3:0]

0x194[7]

0x195[0]

0x196[7:4]

0x196[3:0]

0x197[7]

0x198[0]

0x199[7:4]

0x199[3:0]

0x19A[7]

0x19B[0]

Channel Frequency Division (0, 1, 2, and 3)

For each channel (where the channel number is x: 0, 1, 2, or 3),

the frequency division, DX, is set by the values of M and N

(four bits each, representing decimal 0 to decimal 15), where

Number of Low Cycles = M + 1

Number of High Cycles = N + 1

The cycles are cycles of the clock signal currently routed to the

input of the channel dividers (VCO divider out or CLK).

When a divider is bypassed, DX = 1.

Otherwise, DX = (N + 1) + (M + 1) = N + M + 2. This allows

each channel divider to divide by any integer from 1 to 32.

AD9520-3/PCBZ 数据表(PDF) 45 Page - Analog Devices

AD9520-3/PCBZ 数据表(HTML) 45 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表下载

链接网址

AD9520-3/PCBZ 数据表(PDF) 45 Page - Analog Devices

AD9520-3/PCBZ 数据表(HTML) 45 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表 下载

链接网址

数据表下载