AT91SAM9261 datasheet(41/43 Pages) ATMEL

41 / 43 page

6062KS–ATARM–15-Jan-09

AT91SAM9261 Preliminary

13. Revision History

Table 13-1.

Revision History

Doc.

Rev.

Source

Comments

6062AS

Qualified/Internal: 23-Aug-04

6062BS

Date: 02-Jun-05

CSR 04-370

Change to Additional Embedded Memories in “Features” on page 1. Change to Section 5.2 “Power

Consumption” on page 11. Change to Table 8-3 on page 18.

CSR 04-371

Change to AIC, “Features” on page 1, SMCS signal added to Table 3-1, “Signal Description by

Peripheral,” on page 5, Change to Section 10.3.1.5 “NAND Flash Interface” on page 30.

CSR 04-376

Added NTRST signal to“Block Diagram” on page 4. NTRST signal added to Table 3-1 on page 5. F1

modified in Table 4-1 on page 10. Change to “JTAG Port Pins” on page 11.

CSR 04-446

Changed ROM access to single cycle in “Features” on page 1 and Section 8.1 “Embedded Memories”

on page 17.

CSR 04-447

Replaced “PDMA” with “PDC” throughout. Replaced “Peripheral DMA” with “Peripheral DMA Controller”

throughout.

CSR 04-461

New pinout for 217-ball LFBGA package, Table 2 updated.

CSR 04-475

Updated Section 8.1.2 ”Boot Program” on page 20.

Removed “Embedded Software Services” on page 18.

CSR 05-023

Changed min voltage level for VDDIOM and VDDIOP to 2.7V throughout. Corrected nominal voltage

level for VDDIOP and VDDIOP in Section 5.1 “Power Supplies” on page 11.

CSR 05-024

Added information on chip select assignment management in Section 10.4 “External Bus Interface” on

page 34.

Added information on configuration management of embedded pad pull-up in Section 10.13 “USB” on

page 38.

Throughout document: All references to SmartMedia removed and replaced by NAND Flash. All signals

SMxx changed to NANDxx.

Throughout document: Package now qualified as RoHS-compliant

Changed pull-up resistor level to 10 kOhm in Section 6.4 “PIO Controller A, B and C Lines” on page 12.

Changed typical conditions for VDDCORE to 1.2V in Section 5.2 “Power Consumption” on page 11.

Corrected BMS state in Table 8-3, “Internal Memory Mapping,” on page 18.

Corrected BMS reset condition for ROM access in Section 8.1.1.2 “Internal ROM” on page 19.

6062CS

Date: 15-Nov-05

CSR 05-398

Changed SPI pin names in Figure 2-1, “AT91SAM9261 Block Diagram,” on page 4, Table 3-1, “Signal

Description by Peripheral,” on page 5, Table 10-2, “Multiplexing on PIO Controller A,” on page 31,

Table 10-3, “Multiplexing on PIO Controller B,” on page 32 and Table 10-4, “Multiplexing on PIO

Controller C,” on page 33.

CSR 05-481

Updated A22 pin in Figure 2-1, “AT91SAM9261 Block Diagram,” on page 4.

CSR 05-496

Changed value of programmable pull-up resistor in Section 6.4 “PIO Controller A, B and C Lines” on

page 12.

CSR 05-487

Updated Table 12-1, “AT91SAM9261 Ordering Information,” on page 40.

AT91SAM9261 数据表(PDF) 41 Page - ATMEL Corporation

AT91SAM9261 数据表(HTML) 41 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

数据表下载