| 数据搜索系统,热门电子元器件搜索 |
|
MCP3422 数据表(PDF) 18 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP3422 数据表(HTML) 18 Page - Microchip Technology |
|
18 / 58 page ![]() MCP3422/3/4 DS22088C-page 18 © 2009 Microchip Technology Inc. 5.2 Configuration Register The device has an 8-bit wide configuration register to select for: input channel, conversion mode, conversion rate, and PGA gain. This register allows the user to change the operating condition of the device and check the status of the device operation. The user can rewrite the configuration byte any time during the device operation. Register 5-1 shows the configuration register bits. REGISTER 5-1: CONFIGURATION REGISTER R/W-1 R/W-0 R/W-0 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 RDY C1 C0 O/C S1 S0 G1 G0 1 * 0 * 0 * 1 * 0 * 0 * 0 * 0 * bit 7 bit 0 * Default Configuration after Power-On Reset Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 RDY: Ready Bit This bit is the data ready flag. In read mode, this bit indicates if the output register has been updated with a latest conversion result. In One-Shot Conversion mode, writing this bit to “1” initiates a new conversion. Reading RDY bit with the read command: 1 = Output register has not been updated 0 = Output register has been updated with the latest conversion result Writing RDY bit with the write command: Continuous Conversion mode: No effect One-Shot Conversion mode: 1 = Initiate a new conversion 0 = No effect bit 6-5 C1-C0: Channel Selection Bits 00 = Select Channel 1 (Default) 01 = Select Channel 2 10 = Select Channel 3 (MCP3424 only, treated as “00” by the MCP3422/MCP3423) 11 = Select Channel 4 (MCP3424 only, treated as “01” by the MCP3422/MCP3423) bit 4 O/C: Conversion Mode Bit 1 = Continuous Conversion Mode (Default). The device performs data conversions continuously 0 = One-Shot Conversion Mode. The device performs a single conversion and enters a low power standby mode until it receives another write or read command bit 3-2 S1-S0: Sample Rate Selection Bit 00 = 240 SPS (12 bits) (Default) 01 = 60 SPS (14 bits) 10 = 15 SPS (16 bits) 11 = 3.75 SPS (18 bits) bit 1-0 G1-G0: PGA Gain Selection Bits 00 =x1 (Default) 01 =x2 10 =x4 11 =x8 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |