AT45DB321D datasheet(8/57 Pages) ATMEL

8 / 57 page

3597N–DFLASH–04/09

AT45DB321D

7. Program and Erase Commands

7.1

Buffer Write

Data can be clocked in from the input pin (SI) into either buffer 1 or buffer 2. To load data into the

DataFlash standard buffer (528 bytes), a 1-byte opcode, 84H for buffer 1 or 87H for buffer 2,

must be clocked into the device, followed by three address bytes comprised of 14 don’t care bits

and 10 buffer address bits (BFA9 - BFA0). The 10 buffer address bits specify the first byte in the

buffer to be written. To load data into the binary buffers (512 bytes each), a 1-byte opcode 84H

for buffer 1 or 87H for buffer 2, must be clocked into the device, followed by three address bytes

comprised of 15 don’t care bits and 9 buffer address bits (BFA8 - BFA0). The 9 buffer address

bits specify the first byte in the buffer to be written. After the last address byte has been clocked

into the device, data can then be clocked in on subsequent clock cycles. If the end of the data

buffer is reached, the device will wrap around back to the beginning of the buffer. Data will con-

tinue to be loaded into the buffer until a low-to-high transition is detected on the CS pin.

7.2

Buffer to Main Memory Page Program with Built-in Erase

Data written into either buffer 1 or buffer 2 can be programmed into the main memory. A 1-byte

opcode, 83H for buffer 1 or 86H for buffer 2, must be clocked into the device. For the DataFlash

standard page size (528 bytes), the opcode must be followed by three address bytes consist of

1 don’t care bit, 13 page address bits (PA12 - PA0) that specify the page in the main memory to

be written and 10 don’t care bits. To perform a buffer to main memory page program with built-in

erase for the binary page size (512 bytes), the opcode 83H for buffer 1 or 86H for buffer 2, must

be clocked into the device followed by three address bytes consisting of 2 don’t care bits

13-page address bits (A21 - A9) that specify the page in the main memory to be written and

9 don’t care bits. When a low-to-high transition occurs on the CS pin, the part will first erase the

selected page in main memory (the erased state is a logic 1) and then program the data stored

in the buffer into the specified page in main memory. Both the erase and the programming of the

page are internally self-timed and should take place in a maximum time of tEP. During this time,

the status register and the RDY/BUSY pin will indicate that the part is busy.

7.3

Buffer to Main Memory Page Program without Built-in Erase

A previously-erased page within main memory can be programmed with the contents of either

buffer 1 or buffer 2. A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2, must be clocked into

the device. For the DataFlash standard page size (528 bytes), the opcode must be followed by

three address bytes consist of 1 don’t care bit, 13 page address bits (PA12 - PA0) that specify

the page in the main memory to be written and 10 don’t care bits. To perform a buffer to main

memory page program without built-in erase for the binary page size (512 bytes), the opcode

88H for buffer 1 or 89H for buffer 2, must be clocked into the device followed by three address

bytes consisting of 2 don’t care bits, 13 page address bits (A21 - A9) that specify the page in the

main memory to be written and 9 don’t care bits. When a low-to-high transition occurs on the CS

pin, the part will program the data stored in the buffer into the specified page in the main mem-

ory. It is necessary that the page in main memory that is being programmed has been previously

erased using one of the erase commands (Page Erase or Block Erase). The programming of the

page is internally self-timed and should take place in a maximum time of tP. During this time, the

status register and the RDY/BUSY pin will indicate that the part is busy.

AT45DB321D 数据表(PDF) 8 Page - ATMEL Corporation

AT45DB321D 数据表(HTML) 8 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

数据表下载