STM32F103C8T7 datasheet(16/105 Pages) STMICROELECTRONICS

16 / 105 page

Description

STM32F103x8, STM32F103xB

16/105

Doc ID 13587 Rev 15

in reset mode when VDD is below a specified threshold, VPOR/PDR, without the need for an

external reset circuit.

The device features an embedded programmable voltage detector (PVD) that monitors the

VDD/VDDA power supply and compares it to the VPVD threshold. An interrupt can be

generated when VDD/VDDA drops below the VPVD threshold and/or when VDD/VDDA is higher

than the VPVD threshold. The interrupt service routine can then generate a warning

message and/or put the MCU into a safe state. The PVD is enabled by software.

Refer to Table 11: Embedded reset and power control block characteristics for the values of

VPOR/PDR and VPVD.

2.3.11

Voltage regulator

The regulator has three operation modes: main (MR), low power (LPR) and power down.

●

MR is used in the nominal regulation mode (Run)

●

LPR is used in the Stop mode

●

Power down is used in Standby mode: the regulator output is in high impedance: the

kernel circuitry is powered down, inducing zero consumption (but the contents of the

registers and SRAM are lost)

This regulator is always enabled after reset. It is disabled in Standby mode, providing high

impedance output.

2.3.12

Low-power modes

The STM32F103xx performance line supports three low-power modes to achieve the best

compromise between low power consumption, short startup time and available wakeup

sources:

●

Sleep mode

In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can

wake up the CPU when an interrupt/event occurs.

●

Stop mode

The Stop mode achieves the lowest power consumption while retaining the content of

SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC

and the HSE crystal oscillators are disabled. The voltage regulator can also be put

either in normal or in low power mode.

The device can be woken up from Stop mode by any of the EXTI line. The EXTI line

source can be one of the 16 external lines, the PVD output, the RTC alarm or the USB

wakeup.

●

Standby mode

The Standby mode is used to achieve the lowest power consumption. The internal

voltage regulator is switched off so that the entire 1.8 V domain is powered off. The

PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering

Standby mode, SRAM and register contents are lost except for registers in the Backup

domain and Standby circuitry.

The device exits Standby mode when an external reset (NRST pin), an IWDG reset, a

rising edge on the WKUP pin, or an RTC alarm occurs.

Note:

The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop

or Standby mode.

STM32F103C8T7 数据表(PDF) 16 Page - STMicroelectronics

STM32F103C8T7 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载