JS28F512P30TFA datasheet(23/86 Pages) MICRON

23 / 86 page

Datasheet

Sept 2012

Order Number:208042-0

P30-65nm

7.3

Read CFI

The Read CFI command instructs the device to output Common Flash Interface data

when read. See Figure 6.1, “Device Command Codes” on page 19. Section A.1,

“Common Flash Interface” on page 61 shows CFI information and address offsets

within the CFI database.

7.4

Read Status Register

To read the Status Register, issue the Read Status Register command at any address.

Status Register information is available to which the Read Status Register, Word

Program, or Block Erase command was issued. SRD is automatically made available

following a Word Program, Block Erase, or Block Lock command sequence. Reads from

the device after any of these command sequences outputs the device’s status until

another valid command is written (e.g. the Read Array command).

The Status Register is read using single asynchronous-mode or synchronous burst

mode reads. SRD is output on DQ[7:0], while 0x00 is output on DQ[15:8]. In

asynchronous mode the falling edge of OE#, or CE# (whichever occurs first) updates

and latches the Status Register contents. However, when reading the Status Register in

synchronous burst mode, CE# or ADV# must be toggled to update SRD.

The Device Write Status bit (SR.7) provides overall status of the device. SR[6:1]

present status and error information about the program, erase, suspend, VPP, and

block-locked operations.

See Table 12, “Status Register Description” on page 34 for the description of the Status

7.5

Clear Status Register

The Clear Status Register command clears the Status Register. It functions independent

of VPP. The WSM sets and clears SR[7], but it sets bits SR[5:3,1] without clearing

them. The Status Register should be cleared before starting a command sequence to

avoid any ambiguity. A device reset also clears the Status Register.

Lock Register 1

0x89

PR-LK1 OTP Register lock data

128-bit User-Programmable OTP registers

0x8A–0x109

User OTP Register data

Notes:

BBA = Block Base Address.

DBA = Device base Address, Numonyx reserves other configuration address locations.

The GPR is used as read out register for Extended Function Interface command.

Table 9:

Device ID codes

ID Code Type

Device

Density

Device Identifier Codes

-T

(Top Parameter)

-B

(Bottom Parameter)

-E

(Symmetrical Blocks)

Device Code

512-Mbit

8960

8961

8999

1-Gbit

8962

8963

899A

Note:

The 2-Gbit devices do not have a unique Device ID associated with them. Each die within the stack can be identified by

either of the 1-Gbit Device ID codes depending on its configuration.

Table 8:

Device Identifier Information (Sheet 2 of 2)

Item

Address(1,2)

Data(x16)

JS28F512P30TFA 数据表(PDF) 23 Page - Micron Technology

JS28F512P30TFA 数据表(HTML) 23 Page - Micron Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

数据表下载