ADM1275-1ACPZ-R7 datasheet(39/48 Pages) AD

39 / 48 page

Data Sheet

ADM1275

Rev. D | Page 39 of 48

STATUS_WORD

Code: 0x79, read word. Value after reset: 0x0000.

Table 21. Bit Descriptions for STATUS_WORD Command

Bits

Bit Name

Behavior

Settings

Description

VOUT_STATUS

Live

There are no active status bits to be read by STATUS_VOUT.

There are one or more active status bits to be read by STATUS_VOUT.

IOUT_STATUS

Live

There are no active status bits to be read by STATUS_IOUT.

There are one or more active status bits to be read by STATUS_IOUT.

VIN_STATUS

Live

There are no active status bits to be read by STATUS_INPUT.

There are one or more active status bits to be read by STATUS_INPUT.

MFR_STATUS

Live

There are no active status bits to be read by STATUS_MFR_SPECIFIC.

There are one or more active status bits to be read by STATUS_MFR_SPECIFIC.

POWER_GOOD#

Live

The voltage on the FLB pin is above the required threshold, indicating

that output power is considered good. This bit is the logical inversion of

the PWRGD pin on the part.

The voltage on the FLB pin is below the required threshold, indicating

that output power is considered bad.

[10:8]

Reserved

000

Always reads as 000.

[7:0]

STATUS_BYTE

This byte is the same as the byte returned by the STATUS_BYTE command.

STATUS_VOUT

Code: 0x7A, read byte. Value after reset: 0x00.

This command is supported on the ADM1275-1 and the ADM1275-3. The ADM1275-2 does not have a VOUT pin.

Table 22. Bit Descriptions for STATUS_VOUT Command

Bits

Bit Name

Behavior

Settings

Description

Reserved

Always reads as 0.

VOUT_OV_WARN

Latched

No overvoltage condition on the output supply detected by the power

monitor.

An overvoltage condition on the output supply was detected by the

power monitor.

VOUT_UV_WARN

Latched

No undervoltage condition on the output supply detected by the power

monitor.

An undervoltage condition on the output supply was detected by the

power monitor.

[4:0]

Reserved

00000

Always reads as 00000.

STATUS_IOUT

Code: 0x7B, read byte. Value after reset: 0x00.

Table 23. Bit Descriptions for STATUS_IOUT Command

Bits

Bit Name

Behavior

Settings

Description

IOUT_OC_FAULT

Latched

No overcurrent output fault detected.

The hot-swap controller detected an overcurrent condition and the time

limit set by the capacitor on the TIMER pin has elapsed, causing the hot-

swap gate drive to shut down.

Reserved

Always reads as 0.

IOUT_OC_WARN

Latched

No overcurrent condition on the output supply detected by the power

monitor using the IOUT_OC_WARN_LIMIT command.

An overcurrent condition was detected by the power monitor using the

IOUT_OC_WARN_LIMIT command.

[4:0]

Reserved

00000

Always reads as 00000.

ADM1275-1ACPZ-R7 数据表(PDF) 39 Page - Analog Devices

ADM1275-1ACPZ-R7 数据表(HTML) 39 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载

链接网址

ADM1275-1ACPZ-R7 数据表(PDF) 39 Page - Analog Devices

ADM1275-1ACPZ-R7 数据表(HTML) 39 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表 下载

链接网址

数据表下载