ADM1275-1ACPZ-R7 datasheet(40/48 Pages) AD

40 / 48 page

ADM1275

Data Sheet

Rev. D | Page 40 of 48

STATUS_INPUT

Code: 0x7C, read byte. Value after reset: 0x00.

Table 24. Bit Descriptions for STATUS_INPUT Command

Bits

Bit Name

Behavior

Settings

Description

VIN_OV_FAULT

Latched

No overvoltage detected on the OV pin.

An overvoltage was detected on the OV pin.

VIN_OV_WARN

Latched

No overvoltage condition on the input supply detected by the power

monitor.

An overvoltage condition on the input supply was detected by the power

monitor.

VIN_UV_WARN

Latched

No undervoltage condition on the input supply detected by the power

monitor.

An undervoltage condition on the input supply was detected by the

power monitor.

VIN_UV_FAULT

Latched

No undervoltage detected on the UV pin.

An undervoltage was detected on the UV pin.

[3:0]

Reserved

0000

Always reads as 0000.

STATUS_MFR_SPECIFIC

Code: 0x80, read byte. Value after reset: 0x00.

Table 25. Bit Descriptions for STATUS_MFR_SPECIFIC Command

Bits

Bit Name

Behavior

Settings

Description

FET_HEALTH_BAD

Latched

FET behavior appears to be as expected.

FET behavior suggests that the FET may be shorted.

UV_CMP_OUT

Live

Input voltage to UV pin is above threshold.

Input voltage to UV pin is below threshold.

OV_CMP_OUT

Live

Input voltage to OV pin is below threshold.

Input voltage to OV pin is above threshold.

Reserved

Always reads as 0.

HS_INLIM

Latched

The ADM1275 has not actively limited the current into the load.

The ADM1275 has actively limited current into the load. This bit differs from

the IOUT_OC_FAULT bit in that the HS_INLIM bit is set immediately, whereas

the IOUT_OC_FAULT bit is not set unless the time limit set by the capacitor

on the TIMER pin elapses.

[2:1]

HS_SHUTDOWN_CAUSE

Latched

The ADM1275 is either enabled and working correctly, or has been shut

down using the OPERATION command.

An IOUT_OC_FAULT condition occurred that caused the ADM1275 to shut down.

A VIN_UV_FAULT condition occurred that caused the ADM1275 to shut down.

A VIN_OV_FAULT condition occurred that caused the ADM1275 to shut down.

IOUT_WARN2

Latched

No overcurrent condition on the output supply detected by the power

monitor using the IOUT_WARN2_LIMIT command.

An undercurrent or overcurrent condition on the output supply was

detected by the power monitor using the IOUT_WARN2_LIMIT command.

The polarity of the threshold condition is set by the IOUT_WARN2_SELECT bit

using the DEVICE_CONFIG command.

READ_VIN

Code: 0x88, read word. Value after reset: 0x0000.

Table 26. Bit Descriptions for READ_VIN Command

Bits

Bit Name

Settings

Description

[15:12]

Reserved

0000

Always reads as 0000.

[11:0]

VIN

Input voltage from the SENSE+ pin measurement, expressed in ADC codes.

ADM1275-1ACPZ-R7 数据表(PDF) 40 Page - Analog Devices

ADM1275-1ACPZ-R7 数据表(HTML) 40 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载

链接网址

ADM1275-1ACPZ-R7 数据表(PDF) 40 Page - Analog Devices

ADM1275-1ACPZ-R7 数据表(HTML) 40 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表 下载

链接网址

数据表下载