STM32F217VG datasheet(26/173 Pages) STMICROELECTRONICS

26 / 173 page

Description

STM32F21xxx

26/173

Doc ID 17050 Rev 8

If configured as standard 16-bit timers, they have the same features as the general-purpose

TIMx timers. If configured as 16-bit PWM generators, they have full modulation capability (0-

100%).

The TIM1 and TIM8 counters can be frozen in debug mode. Many of the advanced-control

timer features are shared with those of the standard TIMx timers which have the same

architecture. The advanced-control timer can therefore work together with the TIMx timers

via the Timer Link feature for synchronization or event chaining.

General-purpose timers (TIMx)

There are ten synchronizable general-purpose timers embedded in the STM32F21x devices

(see Table 3 for differences).

●

TIM2, TIM3, TIM4, TIM5

The STM32F21x include 4 full-featured general-purpose timers. TIM2 and TIM5 are

32-bit timers, and TIM3 and TIM4 are 16-bit timers. The TIM2 and TIM5 timers are

based on a 32-bit auto-reload up/downcounter and a 16-bit prescaler. The TIM3 and

TIM4 timers are based on a 16-bit auto-reload up/downcounter and a 16-bit prescaler.

They all feature 4 independent channels for input capture/output compare, PWM or

one-pulse mode output. This gives up to 16 input capture/output compare/PWMs on

the largest packages.

The TIM2, TIM3, TIM4, TIM5 general-purpose timers can work together, or with the

other general-purpose timers and the advanced-control timers TIM1 and TIM8 via the

Timer Link feature for synchronization or event chaining.

The counters of TIM2, TIM3, TIM4, TIM5 can be frozen in debug mode. Any of these

general-purpose timers can be used to generate PWM outputs.

TIM2, TIM3, TIM4, TIM5 all have independent DMA request generation. They are

capable of handling quadrature (incremental) encoder signals and the digital outputs

from 1 to 4 hall-effect sensors.

●

TIM10, TIM11 and TIM9

These timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler.

TIM10 and TIM11 feature one independent channel, whereas TIM9 has two

independent channels for input capture/output compare, PWM or one-pulse mode

output. They can be synchronized with the TIM2, TIM3, TIM4, TIM5 full-featured

general-purpose timers. They can also be used as simple time bases.

●

TIM12, TIM13 and TIM14

These timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler.

TIM13 and TIM14 feature one independent channel, whereas TIM12 has two

independent channels for input capture/output compare, PWM or one-pulse mode

output. They can be synchronized with the TIM2, TIM3, TIM4, TIM5 full-featured

general-purpose timers.

They can also be used as simple time bases.

Basic timers TIM6 and TIM7

These timers are mainly used for DAC trigger and waveform generation. They can also be

used as a generic 16-bit time base.

Independent watchdog

The independent watchdog is based on a 12-bit downcounter and 8-bit prescaler. It is

clocked from an independent 32 kHz internal RC and as it operates independently from the

STM32F217VG 数据表(PDF) 26 Page - STMicroelectronics

STM32F217VG 数据表(HTML) 26 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载