GMS90C31 datasheet(51/59 Pages) HYNIX

51 / 59 page

GMS90 Series

Oct. 2000 Ver 3.1a

EPROM CHARACTERISTICS

The GMS97C5X, 97L5X are programmed by using a modified Quick-Pulse ProgrammingTM algorithm. It dif-

fers from older methods in the value used for VPP (programming supply voltage) and in the width and number

of the ALE/PROG pulses. The GMS97C5X, 97L5X contains two signature bytes that can be read and used by

an EPROM programming system to identify the device. The signature bytes identify the device as an manufac-

tured by HME. Table 11 shows the logic levels for reading the signature byte, and for programming the program

memory, the encryption table, and the security bits. The circuit configuration and waveforms for quick-pulse

programming are shown in Figure 12 and Figure 13. Figure 14 show the circuit configuration for normal pro-

gram memory verification.

Reading the Signature Bytes :

The GMS97X51/52 signature bytes in locations 030H and 031H, the GMS97X54/56/58 signature bytes in loca-

tions 05EH and 07CH. To read these bytes follow the procedure for EPROM verify, except that P3.6 and P3.7

need to be pulled to a logic low.

The values are:

Quick-pulse programming

The setup for microcontroller quick-pulse programming is shown in Figure 13. Note that the GMS97C5X,

97L5X is running with a 4 to 6MHz oscillator. The reason the oscillator needs to be running is that the device

is executing internal address and program data transfers.

The address of the EPROM location to be programmed is applied to ports 1 and 2, as shown in Figure 12. The

code byte to be programmed into that location is applied to port 0, RST, PSEN andpins ofport2 and3 in Table

11 are held at the "Program Code Data" levels indicated in Table 11. The ALE/PROG is pulsed low 25 times(10

times for 97X54/56/58) as shown Figure 13.

To program the encryption table, repeat the 25 pulses (10 pulses for 97X54/56/58) programming sequence for

addresses 0 through 1FH(3FH for 97X54/56/58), using the "Program Encryption Table" levels. Do not forget

that after the encryption table is programmed, verification cycles will produce only encrypted data.

To program the security bits, repeat the 25 pulses (10 pulses for 97X54/56/58) programming sequence using the

"Pgm Security Bit" levels after one security bit is programmed, further programming of the code memory and

Device

Location

Contents

Remarks

GMS97X51

30H

31H

E0H

73H

Manufacturer ID

Device ID

GMS97X52

30H

31H

E0H

71H

Manufacturer ID

Device ID

GMS97X54

5EH

7CH

E0H

54H

Manufacturer ID

Device ID

GMS97X56

5EH

7CH

E0H

56H

Manufacturer ID

Device ID

GMS97X58

5EH

7CH

E0H

58H

Manufacturer ID

Device ID

GMS90C31 数据表(PDF) 51 Page - Hynix Semiconductor

GMS90C31 数据表(HTML) 51 Page - Hynix Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

数据表下载

链接网址

GMS90C31 数据表(PDF) 51 Page - Hynix Semiconductor

GMS90C31 数据表(HTML) 51 Page - Hynix Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

数据表 下载

链接网址

数据表下载