FT260Q-R datasheet(14/61 Pages) FTDI

14 / 61 page

FT260 HID-CLASS USB TO UART/I2C BRIDGE IC

Version 1.1

Document No.: FT_001272 Clearance No.: FTDI#484

generates 48MHz, 24MHz and 12MHz as reference clocks. The user can select one of these reference

clocks as the system operating clock through software over USB. The system operating clock will be the

clock source for embedded functions to generate the required interface clock. Higher frequencies should

be chosen for higher data throughput demand and lower frequencies for lower power operation. Users

can choose the system operating frequency based on the application.

USB Transceiver. The USB Transceiver cell provides the USB 1.1 / USB 2.0 full-speed physical interface.

Output drivers provide +3.3V level slew rate control , while a differential input and two single ended

input receivers provide data in, Single-Ended-0 (SE0) and USB reset detection conditions respectfully. A

1.5kΩ pull up resistor on USBDP is incorporated.

USB DPLL. The DPLL cell locks on to the incoming NRZI USB data and generates recovered clock and

data signals for the Serial Interface Engine (SIE) block.

Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial

and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it

performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data

stream.

USB HID Protocol Engine. The USB HID Protocol Engine manages the standard commands from the

device control pipe when enumerating. It also handles the Human Interface Device (HID) class

commands between the standard HID host driver and the device with I2C or/and UART functions. With

the Device Interface Configuration pins, DCNF0 and DCNF1, it can easily connect HID functions via UART

or I2C interfaces to a PC host driver. Additionally, it can simultaneously support 2 HID functions via UART

and I2C interfaces. This Protocol Engine also includes an IN and OUT Buffer management memory unit

which handles the data between USB endpoints and function interfaces such as UART and I2C.

The USB HID Protocol Engine includes:



Endpoint-0 for a control pipe with max packet size 64 Bytes



2 endpoints for interrupt-in pipe with max packet size equal to 64 Bytes



2 endpoints for interrupt-out pipe with max packet size up to 64 Bytes



Multiple interfaces configuration support



HID class-specific request parsing and transporting to I2C/UART bus interface



command Suspend detection and power management



Remote wake-up support



Fully compatible to USB2.0 specification requirement in full speed mode

OUT Buffer. Data sent from the USB host controller to the FT260 via the USB data OUT endpoint is

stored in the OUT buffer. Data is removed from the OUT buffer to function interfaces under the control of

the USB HID protocol engines. The endpoint buffer size is 64 bytes as the maximum packet size defined

for full speed transferring. For the interrupt pipe, the buffer is double buffered for increased throughput.

IN Buffer. Data from the function interfaces is stored in the IN buffer. The USB host controller removes

data from the IN buffer by sending a USB request for data from the device data IN endpoint. The

endpoint buffer size is 64 bytes as the maximum packet size defined for full speed transferring. For the

interrupt pipe, the buffer is double buffered for increased throughput.

UART Controller. When the data and control bus are configured in UART mode, the interface

implements a standard asynchronous serial UART port with flow control. The UART performs

asynchronous 7/8 bit Parallel to Serial and Serial to Parallel conversion of the data on the RS232 (RS422

and RS485) interface. Control signals supported by the UART include RTS, CTS, DTR, DSR, DCD and RI.

FT260Q-R 数据表(PDF) 14 Page - Future Technology Devices International Ltd.

FT260Q-R 数据表(HTML) 14 Page - Future Technology Devices International Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

数据表下载