S29AL008D55BAI011 datasheet(29/55 Pages) SPANSION

29 / 55 page

June 16, 2005 S29AL008D_00A3

S29AL008D

Da t a

S h ee t

If the output is low (Busy), the device is actively erasing or programming. (This

includes programming in the Erase Suspend mode.) If the output is high (Ready),

the device is ready to read array data (including during the Erase Suspend

mode), or is in the standby mode.

Table 6, on page 32 shows the outputs for RY/BY#. Figure 13, on page 38, Figure

14, Figure 17, on page 43 and Figure 18, on page 44 shows RY/BY# for read,

reset, program, and erase operations, respectively.

DQ6: Toggle Bit I

Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm

is in progress or complete, or whether the device entered the Erase Suspend

mode. Toggle Bit I may be read at any address, and is valid after the rising edge

of the final WE# pulse in the command sequence (prior to the program or erase

operation), and during the sector erase time-out.

During an Embedded Program or Erase algorithm operation, successive read cy-

cles to any address cause DQ6 to toggle. (The system may use either OE# or CE#

to control the read cycles.) When the operation is complete, DQ6 stops toggling.

After an erase command sequence is written, if all sectors selected for erasing

are protected, DQ6 toggles for approximately 100 µs, then returns to reading

array data. If not all selected sectors are protected, the Embedded Erase algo-

rithm erases the unprotected sectors, and ignores the selected sectors that are

protected.

The system can use DQ6 and DQ2 together to determine whether a sector is ac-

tively erasing or is erase-suspended. When the device is actively erasing (that is,

the Embedded Erase algorithm is in progress), DQ6 toggles. When the device en-

ters the Erase Suspend mode, DQ6 stops toggling. However, the system must

also use DQ2 to determine which sectors are erasing or erase-suspended. Alter-

natively, the system can use DQ7 (see the subsection DQ7: Data# Polling, on

page 27).

If a program address falls within a protected sector, DQ6 toggles for approxi-

mately 1 µs after the program command sequence is written, then returns to

reading array data.

DQ6 also toggles during the erase-suspend-program mode, and stops toggling

once the Embedded Program algorithm is complete.

Table 6, on page 32 shows the outputs for Toggle Bit I on DQ6. Figure 6, on page

31 shows the toggle bit algorithm. Figure 20, on page 45 shows the toggle bit

timing diagrams. Figure 21, on page 46 shows the differences between DQ2 and

DQ6 in graphical form. See also the subsection DQ2: Toggle Bit II, on page 29.

DQ2: Toggle Bit II

The Toggle Bit II on DQ2, when used with DQ6, indicates whether a particular

sector is actively erasing (that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit II is valid after the rising

edge of the final WE# pulse in the command sequence.

DQ2 toggles when the system reads at addresses within those sectors that were

selected for erasure. (The system may use either OE# or CE# to control the read

cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is

erase-suspended. DQ6, by comparison, indicates whether the device is actively

erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected

S29AL008D55BAI011 数据表(PDF) 29 Page - SPANSION

S29AL008D55BAI011 数据表(HTML) 29 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

数据表下载