ADGM1004JCPZ-R2 datasheet(5/32 Pages) AD

5 / 32 page

Data Sheet

ADGM1004

Rev. D | Page 5 of 32

SPECIFICATIONS

Supply voltage (VDD) = 3.0 V to 3.6 V, GND = 0 V, and all specifications at TA = 25°C, unless otherwise noted. Typical specifications tested

at TA = 25°C with VDD = 3.3 V.

Table 1.

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments1

ON-RESISTANCE PROPERTIES

See Figure 6 to Figure 13 for more details

Initial On-Resistance

Properties

On Resistance

RON

2.9

Drain source current (IDS) = 50 mA, 0 V input bias,

at 1 ms after first actuation, maximum

specification from 0°C to 85°C

On-Resistance Match

Between Channels

ΔRON CH_CH

Maximum value tested from 0°C to 85°C

On-Resistance Drift

Over Time2

ΔRON TIME

−0.25

RON changed from 1 ms to 100 ms after first

actuation, maximum value tested from 0°C to 85°C

Over Actuations3

ΔRON

0.5

109 actuations, switch is actuated at 25°C and

RON is measured at 25°C

109 actuations, switch is actuated at 85°C and RON is

measured at 25°C, 1 kHz actuating frequency,

220 mA load applied between toggles4

RELIABILITY PROPERTIES

Continuously On Lifetime

7.2

Years

Median time before failure at 50°C5, see Figure 60

for more details

Actuation Lifetime

Cold Switched

109

Actuations

Load between toggling is 220 mA, tested at 85°C

Hot Switched

RF power = continuous wave (CW), terminated

into 50 Ω, see Figure 14 for details

10 dBm

5.16 ×

109

Actuations

50% of test population failure point (T50)

15 dBm

3.21 ×

106

Actuations

50% of test population failure point (T50)

20 dBm

390 ×

103

Actuations

50% of test population failure point (T50)

DYNAMIC CHARACTERISTICS

Operating Frequency

0/dc

GHz

−3 dB Bandwidth

RF1, RF4

9.5

10.8

GHz

RF1 to RFC and RF4 to RFC channels

RF2, RF3

11.5

GHz

RF2 to RFC and RF3 to RFC channels

Insertion Loss

0.45

0.6

At 2.5 GHz, RFC to RFx

0.63

0.95

At 6.0 GHz, RFC to RFx

Isolation

RFx to RFC

At 2.5 GHz, RFx to RFC (all channels off )

At 6.0 GHz, RFx to RFC (all channels off )

RF1 to RFC

At 6 GHz, RF2 to RFC is on, RF1 to RFC is off

RF2 to RFC

At 6 GHz, RF1 to RFC is on, RF2 to RFC is off

Crosstalk

At 2.5 GHz, RFx to RFx

At 6.0 GHz, RFx to RFx

Return Loss

DC to 6.0 GHz

Third-Order Intermodulation

Intercept

IP3

dBm

Input: 900 MHz and 901 MHz, input power =

27 dBm

Second-Order Intermodulation

Intercept

IP2

dBm

Input: 900 MHz and 901 MHz, input power =

27 dBm

Second Harmonic Distortion

HD2

−90

dBc

Input: 5.4 MHz, input power = 0 dBm

−74

dBc

Input: 150 MHz and 800 MHz, input power =

27 dBm

ADGM1004JCPZ-R2 数据表(PDF) 5 Page - Analog Devices

ADGM1004JCPZ-R2 数据表(HTML) 5 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表下载

链接网址

ADGM1004JCPZ-R2 数据表(PDF) 5 Page - Analog Devices

ADGM1004JCPZ-R2 数据表(HTML) 5 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表 下载

链接网址

数据表下载