ST7LITE3 datasheet(12/167 Pages) STMICROELECTRONICS

12 / 167 page

ST7LITE3

12/167

FLASH PROGRAM MEMORY (Cont’d)

4.4 ICC interface

ICP needs a minimum of 4 and up to 6 pins to be

connected to the programming tool. These pins

are:

– RESET: device reset

–VSS: device power supply ground

– ICCCLK: ICC output serial clock pin

– ICCDATA: ICC input serial data pin

– PB4/OSC1: main clock input for external

source (not required on devices without

OSC1/OSC2 pins)

–VDD: application board power supply (option-

al, see Note 3)

Notes:

1. If the ICCCLK or ICCDATA pins are only used

as outputs in the application, no signal isolation is

necessary. As soon as the Programming Tool is

plugged to the board, even if an ICC session is not

in progress, the ICCCLK and ICCDATA pins are

not available for the application. If they are used as

inputs by the application, isolation such as a serial

resistor has to be implemented in case another de-

vice forces the signal. Refer to the Programming

Tool documentation for recommended resistor val-

ues.

2. During the ICP session, the programming tool

must control the RESET pin. This can lead to con-

flicts between the programming tool and the appli-

cation reset circuit if it drives more than 5mA at

high level (push pull output or pull-up resistor<1K).

A schottky diode can be used to isolate the appli-

cation RESET circuit in this case. When using a

classical RC network with R>1K or a reset man-

agement IC with open drain output and pull-up re-

sistor>1K, no additional components are needed.

In all cases the user must ensure that no external

reset is generated by the application during the

ICC session.

3. The use of Pin 7 of the ICC connector depends

on the Programming Tool architecture. This pin

must be connected when using most ST Program-

ming Tools (it is used to monitor the application

power supply). Please refer to the Programming

Tool manual.

4. Pin 9 has to be connected to the PB4 pin of the

ST7 when the clock is not available in the applica-

tion or if the selected clock option is not pro-

grammed in the option byte. ST7 devices with mul-

ti-oscillator capability need to have OSC2 ground-

ed in this case.

Caution: During normal operation ICCCLK pin

must be pulled- up, internally or externally (exter-

nal pull-up of 10k mandatory in noisy environ-

ment). This is to avoid entering ICC mode unex-

pectedly during a reset. In the application, even if

the pin is configured as output, any reset will put it

back in input pull-up.

Figure 4. Typical ICC Interface

ICC CONNECTOR

HE10 CONNECTOR TYPE

APPLICATION

POWER SUPPLY

PROGRAMMING TOOL

ICC CONNECTOR

APPLICATION BOARD

ICC Cable

(See Note 3)

ST7

CL2

CL1

OPTIONAL

See Note 1

See Note 1 and caution

See Note 2

APPLICATION

RESET SOURCE

APPLICATION

I/O

(See Note 4)

Note with the ICP option disabled with ST7 MDT10-EPB that the external clock has to be provided on PB4

ST7LITE3 数据表(PDF) 12 Page - STMicroelectronics

ST7LITE3 数据表(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7LITE3 数据表(PDF) 12 Page - STMicroelectronics

ST7LITE3 数据表(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载