USB82642 datasheet(34/64 Pages) MICROCHIP

34 / 64 page

USB82642

DS60001253F-page 34

 2012-2021 Microchip Technology Inc.

7.5.3.22

ECh: Hub Controller Max Current For Self-Powered Operation

7.5.3.23

EDh: Hub Controller Max Current For Bus-Powered Operation

7.5.3.24

EEh: Power-On Time

7.5.3.25

EFh: Boost_Up

Bit

Name

Description

7:0

HC_MAX_C_SP

Value in 2 mA increments that the hub consumes from an upstream port

(VBUS) when operating as a self-powered hub. This value includes the hub

silicon along with the combined power consumption (from VBUS) of all asso-

ciated circuitry on the board. This value does NOT include the power con-

sumption of a permanently attached peripheral if the hub is configured as a

compound device.

Note:

The USB 2.0 Specification [3] does not permit this value to exceed

100 mA.

A value of 50 (decimal) indicates 100 mA, which is the default value.

Bit

Name

Description

7:0

HC_MAX_C_BP

Value in 2 mA increments that the hub consumes from an upstream port

(VBUS) when operating as a bus-powered hub. This value will include the

hub silicon along with the combined power consumption (from VBUS) of all

associated circuitry on the board. This value will NOT include the power con-

sumption of a permanently attached peripheral if the hub is configured as a

compound device.

A value of 50 (decimal) would indicate 100 mA, which is the default value.

Bit

Name

Description

7:0

POWER_ON_TIME

The length of time that it takes (in 2 ms intervals) from the time the host initi-

ated power-on sequence begins on a port until power is adequate on that

port. If the host requests the power-on time, the system software uses this

value to determine how long to wait before accessing a powered-on port.

Bit

Name

Description

7:2

rsvd

1:0

BOOST_IOUT

USB electrical signaling drive strength boost bit for the upstream port ‘A’.

: normal electrical drive strength = no boost

: elevated electrical drive strength = low (approximately 4% boost)

: elevated electrical drive strength = medium (approximately 8% boost)

: elevated electrical drive strength = high (approximately 12% boost)

Note:

“Boost” could result in non-USB Compliant parameters. OEM

should use a 00 value unless specific implementation issues

require additional signal boosting to correct for degraded USB sig-

naling levels.

USB82642 数据表(PDF) 34 Page - Microchip Technology

USB82642 数据表(HTML) 34 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

数据表下载

链接网址

USB82642 数据表(PDF) 34 Page - Microchip Technology

USB82642 数据表(HTML) 34 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

数据表 下载

链接网址

数据表下载