SST26VF032BEUI datasheet(8/76 Pages) MICROCHIP

8 / 76 page

SST26VF032BEUI

DS20006152A-page 8

 2019 Microchip Technology Inc.

4.3

Security ID

SST26VF032BEUI offers a 2 KByte Security ID (Sec

ID) feature. The Security ID space is divided into two

parts – one factory-programmed, 64-bit segment and

one user-programmable segment. The factory-pro-

grammed segment is programmed during manufactur-

ing with a unique number and cannot be changed. The

user-programmable segment is left unprogrammed for

the customer to program as desired.

Use the Program Security ID (PSID) command to pro-

gram the Security ID using the address shown in Table

5-5. The Security ID can be locked using the Lockout

Security ID (LSID) command. This prevents any future

write operations to the Security ID.

The factory-programmed portion of the Security ID

can’t be programmed by the user; neither the factory-

programmed nor user-programmable areas can be

erased.

4.4

Hold Operation

The HOLD# pin pauses active serial sequences with-

out resetting the clocking sequence. This pin is active

after every power up and only operates during SPI

single-bit and dual-bit modes. Two factory configura-

tions are available: SST26VF032BEUI ships with the

IOC bit set to ‘0’ and the HOLD# pin function enabled;

SST26VF032BEUI ships with the IOC bit set to ‘1’ and

the HOLD# pin function disabled. The HOLD# pin is

always disabled in SQI mode and only works in SPI sin-

gle-bit and dual-bit read mode.

To activate the Hold mode, CE# must be in active low

state. The Hold mode begins when the SCK active low

state coincides with the falling edge of the HOLD# sig-

nal. The Hold mode ends when the HOLD# signal’s ris-

ing edge coincides with the SCK active low state.

If the falling edge of the HOLD# signal does not coin-

cide with the SCK active low state, then the device

enters Hold mode when the SCK next reaches the

active low state. Similarly, if the rising edge of the

HOLD# signal does not coincide with the SCK active

low state, then the device exits Hold mode when the

SCK next reaches the active low state. See Figure 4-3.

Once the device enters Hold mode, SO will be in high

impedance state while SI and SCK can be VIL or VIH.

If CE# is driven active high during a Hold condition, it

resets the internal logic of the device. As long as

HOLD# signal is low, the memory remains in the Hold

condition. To resume communication with the device,

HOLD# must be driven active high, and CE# must be

driven active low.

FIGURE 4-3:

HOLD CONDITION WAVEFORM.

TABLE 4-1:

WRITE PROTECTION LOCK-DOWN STATES

WP#

IOC

WPEN

WPLD

Execute WBPR Instruction

Configuration Register

Not Allowed

Protected

Not Allowed

Writable

Not Allowed

Protected

L01

Allowed

Writable

Not Allowed

Writable

Allowed

Writable

Not Allowed

Writable

X13

Allowed

Writable

1. Default at power-up Register settings for SST26VF032BEUI

2. Factory default setting is ‘0’. This is a non-volatile bit; default at power-up is the value set prior to power-down.

3. Default at power-up Register settings for SST26VF032BEUI

Active

Hold

Active

Hold

Active

20005218 F46.0

SCK

HOLD#

SST26VF032BEUI 数据表(PDF) 8 Page - Microchip Technology

SST26VF032BEUI 数据表(HTML) 8 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

数据表下载

链接网址

SST26VF032BEUI 数据表(PDF) 8 Page - Microchip Technology

SST26VF032BEUI 数据表(HTML) 8 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

数据表 下载

链接网址

数据表下载