KSZ9563R datasheet(38/226 Pages) MICROCHIP

38 / 226 page

KSZ9563R

DS00002419D-page 38

 2017-2018 Microchip Technology Inc.

By default tail tagging is disabled. To Enable it, set the Tail Tag Enable bit in one of the Port Operation Control 0 Register

at address 0xN020 for port “N”. When this bit is set for one port, that port is referred to as the “host” port. Do not set the

Tail Tag Enable bit for more than one port.

When IEEE 1588 Precision Time Protocol (PTP) Mode is enabled, the format of the tail tag changes. Specifically, a four

byte timestamp field is added between the payload and the tail tag as shown in Figure 4-6. PTP mode is enabled by

setting bit 6 in Global PTP Message Config 1 Register. Note that the KSZ8441/62/63 use a different method for passing

the timestamp between the switch and host.

In the switch-to-host direction, the switch sets the PTP Message Indication bit in the tail tag to indicate when the four-

byte receive timestamp is present. When PTP Message Indication is not set, the four-byte timestamp field is not present.

It is therefore essential for the host processor to read bit 7 of each tail tag in order to know the packet format.

The 32-bit timestamp consists of 2 bits for “seconds” and 30 bits for “nanoseconds”. The timestamp format is:

(((second & 3) << 30) | nanosecond).

In the host-to-switch direction, the 4-byte timestamp field is always present when PTP is enabled, as shown in Figure 4-

6. This is true for all packets sent by the host, including IBA packets. The host uses this field to insert the receive time-

stamp from PTP Pdelay_Req messages into the Pdelay_Resp messages. For all other traffic and PTP message types,

the host should populate the timestamp field with zeros.

4.4.10

IGMP SUPPORT

For Internet Group Management Protocol (IGMP) support in Layer 2, the device provides two components:

• “IGMP” Snooping

• “Multicast Address Insertion” in the Static MAC Table

4.4.10.1

“IGMP” Snooping

The device traps IGMP packets and forwards them only to the processor (host port). The IGMP packets are identified

as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4 and protocol version

number = 0x2.

4.4.10.2

“Multicast Address Insertion” in the Static MAC Table

Once the multicast address is programmed in the Static Address Table or Address Lookup Table, the multicast session

is trimmed to the subscribed ports, instead of broadcasting to all ports.

So that the host processor knows which port the IGMP packet was received on, Tail Tagging Mode must be enabled.

4.4.11

IPV6 MLD SNOOPING

The device traps IPv6 Multicast Listener Discovery (MLD) packets and forwards them only to the processor (host port).

Forward to Port 3

Forward to Port 2

Forward to Port 1

FIGURE 4-6:

TAIL TAG FRAME FORMAT IN PTP MODE

Note:

The port for which Tail Tagging Mode is enabled is the host port.

TABLE 4-14:

TRANSMIT TAIL TAG FORMAT (FROM HOST TO SWITCH) (CONTINUED)

Bits

Description

DESTINATION

ADDRESS

SOURCE

ADDRESS

802.1Q

TAG

(4)

ETYPE or

LENGTH

TIME

STAMP

PAYLOAD

46 (42) - 1500

FCS

BYTES

TAIL

TAG

KSZ9563R 数据表(PDF) 38 Page - Microchip Technology

KSZ9563R 数据表(HTML) 38 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载