PIC18F258-ESLASHPSQTP datasheet(84/402 Pages) MICROCHIP

84 / 402 page

PIC18FXX8

DS41159E-page 82

8.2

PIR Registers

The Peripheral Interrupt Request (PIR) registers

contain the individual flag bits for the peripheral

interrupts (Register 8-4 through Register 8-6). Due to

the number of peripheral interrupt sources, there are

three Peripheral Interrupt Request (Flag) registers

(PIR1, PIR2, PIR3).

PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1

Note 1: Interrupt flag bits are set when an interrupt

condition occurs regardless of the state of

its corresponding enable bit or the Global

Interrupt

Enable

bit,

GIE

(INTCON

2: User software should ensure the appropri-

ate interrupt flag bits are cleared prior to

enabling an interrupt and after servicing

that interrupt.

R/W-0

R-0

R/W-0

PSPIF(1)

ADIF

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

bit 7

bit 0

bit 7

PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit(1)

= A read or a write operation has taken place (must be cleared in software)

= No read or write has occurred

bit 6

ADIF: A/D Converter Interrupt Flag bit

= An A/D conversion completed (must be cleared in software)

= The A/D conversion is not complete

bit 5

RCIF: USART Receive Interrupt Flag bit

= The USART receive buffer, RCREG, is full (cleared when RCREG is read)

= The USART receive buffer is empty

bit 4

TXIF: USART Transmit Interrupt Flag bit

= The USART transmit buffer, TXREG, is empty (cleared when TXREG is written)

= The USART transmit buffer is full

bit 3

SSPIF: Master Synchronous Serial Port Interrupt Flag bit

= The transmission/reception is complete (must be cleared in software)

= Waiting to transmit/receive

bit 2

CCP1IF: CCP1 Interrupt Flag bit

Capture mode:

= A TMR1 register capture occurred (must be cleared in software)

= No TMR1 register capture occurred

Compare mode:

= A TMR1 register compare match occurred (must be cleared in software)

= No TMR1 register compare match occurred

PWM mode:

Unused in this mode.

bit 1

TMR2IF: TMR2 to PR2 Match Interrupt Flag bit

= TMR2 to PR2 match occurred (must be cleared in software)

= No TMR2 to PR2 match occurred

bit 0

TMR1IF: TMR1 Overflow Interrupt Flag bit

= TMR1 register overflowed (must be cleared in software)

= TMR1 register did not overflow

Note 1: This bit is only available on PIC18F4X8 devices. For PIC18F2X8 devices, this bit

is unimplemented and reads as ‘0’.

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC18F258-E/PSQTP 数据表(PDF) 84 Page - Microchip Technology

PIC18F258-E/PSQTP 数据表(HTML) 84 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载