STW5094AD datasheet(10/51 Pages) STMICROELECTRONICS

10 / 51 page

STw5094A

10/51

2.7 FM Input Path

The device is provided with stereo and mono single ended analog inputs, designed to amplify analog sig-

nals from an FM decoder but they can be considered as generic analog inputs. The stereo analog inputs

are FML and FMR pins, or alternatively MIC3 pin for mono input (sent to left and right channels). The se-

lection between FML-FMR or MIC3 is done with bit MFM in CR20.

The analog inputs are connected to a programmable gain stage that can amplify the signals in the range -20dB

to +18dB in 2 dB steps. The gain control is independent for Left and Right channel and is selected with bits

FMLA in CR10 (Left) and bits FMRA in CR11 (Right).

There are 2 ways to connect the FM inputs to the output drivers. The first is to select the FM Mode (bits

MD in CR21). The second is to activate Audio or Voice or Tone Only modes and to set to 1 bit FMS in

CR20. In the last case the signal coming from FM inputs will be summed to the Audio or Voice or Tones

signals respectively.

2.8 Output Drivers section

There are 3 Analog Output Drivers. The LSP

⁄ N differential driver delivers 300mW typical power with

0.1% T.H.D. (250mW minimum undistorted) on a 8

Ω earpiece ⁄ loudspeaker (piezoceramic loads up to

50nF can also be driven with a series resistor), it has a 30dB range gain control (bits LSA in CR7). The 2

single ended drivers (HPL and HPR) deliver 40mW typical power with 0.1% T.H.D. (30mW minimum un-

distorted) on 16

Ω stereo headphones, they have a 40dB range gain control (CR8 for HPL and CR9 for

HPR). It is possible to put the drivers in power-down and in power-up by programming bits PLS, PHL, PHR

in CR6. These settings are not dependent from the selected operative Mode.

The common mode voltage of all the drivers is selected with bits VCL in CR18 in the range 1.2V to 1.65V

with 150mV steps. This feature is useful to set the common mode voltage to VCCP/2 and therefore to ex-

tend the output range and increase the output power.

If HPL and HPR are enabled together in Voice Mode or Tone Only Mode the same signal is sent to both

Drivers. The active Drivers can be muted (keeping them in power-up state) using bit MUT in CR6. At pow-

er-up or after a change in PLS or PHL or PHR bits the outputs are muted for 10 ms to avoid unwanted

noise. The transient suppression filter is used to avoid clicks when the gain value is changed.

2.9 Common Mode Driver

The common mode voltage driver (VCMHP pin) simplifies the application for a stereo headset connection

saving two decoupling capacitors in series with HPL and HPR. The loads of the single ended drivers are

connected on one side to HPL and HPR respectively, and on the other to VCMHP, that has the same com-

mon mode voltage. The driver is enabled with bit VCE in CR18.

The output voltage of VCMHP is selected with bits VCL in CR18 in the range 1.2V to 1.65V with 150mV

steps.

2.10 Tone Generator

The Tone Generator can be activated (writing CR12) in all the STw5094A operating modes except FM

mode. In Voice and Audio modes the tones are summed to the signal. It is possible to generate 1 or 2

summed waveforms (either sinusoidal or square wave), their frequencies can be set in CR13 for the first

one (f1) and in CR14 for the second one (f2) accordingly to the values listed in Table 1 if the active master

clock is MCLK or AUXCLK. If the active master clock is AMCK the frequency values specified in Table 1

must be multiplied by a factor kfAMCK that depends on the AMCK frequency value. The amplitude of the

generated waveform can be regulated in CR12 over a 33dB range. When both f1 and f2 are selected the

amplitude of f1 and f2 are lowered by 5dB and 7dB respectively with respect to the amplitude of a single

waveform. In this way the amplitude of the summed waveforms does not overload and there is a 2dB dif-

ference between f1 and f2 amplitude as required for DTMF generation. The Tone Generator output can

be sent to the Voice Transmit section (in Voice Mode), to the Power amplifiers, possibly mixed with audio

or voice, (in all the modes except FM mode) and to the buzzer output BZ (in all the modes except FM

mode).

STW5094AD 数据表(PDF) 10 Page - STMicroelectronics

STW5094AD 数据表(HTML) 10 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表下载