ADE7569 datasheet(25/144 Pages) AD

25 / 144 page

ADE7566/ADE7569/ADE7166/ADE7169

Rev. A | Page 25 of 144

POWER MANAGEMENT

The ADE7566/ADE7569/ADE7166/ADE7169 have elaborate

power management circuitry that manages the regular power

supply to battery switchover and power supply failures. The

power management functionalities can be accessed directly

through the 8052 SFRs (see Table 15).

Table 15. Power Management SFRs

SFR Address

R/W

Mnemonic

Description

0xEC

R/W

IPSME

Power Management Interrupt Enable. See Table 20.

0xF5

R/W

BATPR

Battery Switchover Configuration. See Table 18.

0xF8

R/W

IPSMF

Power Management Interrupt Flag. See Table 17.

0xFF

R/W

INTPR

Interrupt Pins Configuration. See Table 16.

0xF4

R/W

PERIPH

Peripheral Configuration SFR. See Table 19.

0xC5

R/W

POWCON

Power Control. See Table 25.

0xFB

R/W

SCRATCH1

Scratch Pad 1. See Table 21.

0xFC

R/W

SCRATCH2

Scratch Pad 2. See Table 22.

0xFD

R/W

SCRATCH3

Scratch Pad 3. See Table 23.

0xFE

R/W

SCRATCH4

Scratch Pad 4. See Table 24.

POWER MANAGEMENT REGISTER DETAILS

Table 16. Interrupt Pins Configuration SFR (INTPR, 0xFF)

Bit

Mnemonic

Default

Description

RTCCAL

Controls RTC calibration output. When set, the RTC calibration frequency selected by FSEL[1:0] is

output on the P0.2/CF1/RTCCAL pin.

Sets RTC calibration output frequency and calibration window.

FSEL[1:0]

Result (Calibration window, frequency)

30.5 sec, 1 Hz

30.5 sec, 512 Hz

0.244 sec, 500 Hz

6 to 5

FSEL[1:0]

0.244 sec, 16.384 kHz

Reserved

Controls the function of INT1.

INT1PRG[2:0]

Result

X00

GPIO enabled

X01

BCTRL enabled

01X

INT1 input disabled

3 to 1

INT1PRG[2:0]

000

11X

INT1 input enabled

Controls the function of INT0.

INT0PRG

Result

INT0 input disabled

INT0PRG

INT0 input enabled

Writing to the Interrupt Pins Configuration SFR (INTPR, 0xFF)

To protect the RTC from runaway code, a key must be written to the Key SFR (KYREG, 0xC1) to obtain write access to INTPR. KYREG

(see Table 116) should be set to 0xEA to unlock this SFR and reset to zero after a timekeeping register is written to. The RTC registers can

be written using the following 8052 assembly code:

MOV

KYREG, #0EAh

MOV

INTPR, #080h

ADE7569 数据表(PDF) 25 Page - Analog Devices

ADE7569 数据表(HTML) 25 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载